In this repair guide, we show you how to replace your SHIFT6m defective rear camera on your own. You need this repair if the rear camera isn’t working, your pictures are blurry, or the camera doesn’t focus.

Click the small Play button in the top right of an image to play a video for each step.

Required tools

  • Hard Plastic Picks

    Hard Plastic Picks

    You need a flat but stable tool such as a pick to pry out parts that are glued in place.

    €3.00 at the iDoc store
  • Plastic prying tool

    Plastic prying tool

    You need a flat plastic prying tool to disconnect the various plugs and connectors.

    €3.00 at the iDoc store
  • Torx T3 screwdriver

    Torx T3 screwdriver

    You need the right screwdriver for removing Torx T3 screws.

    €16.00 at the iDoc store
Show all replacement parts for the SHIFT6m 

Replacement parts and tools for this repair

Our tools plus the right spare part help you fix your device easily.

for €49.00

Getting started with the repair of your SHIFT6m

If you get stuck or have questions, you can post a comment. We’d be happy to help.

9 steps
  1. Switch off the device

    SHIFT6m - Switch off the device 01
    SHIFT6m - Switch off the device 02
    SHIFT6m - Switch off the device 03
    1. Turn off your device by holding down the power button until the “Power off” option appears.
    2. Use your finger to confirm that you want to shut down your SHIFT6m and wait until the screen goes blank.
  2. Remove the back cover

    SHIFT6m - Remove the back cover 01
    SHIFT6m - Remove the back cover 02
    SHIFT6m - Remove the back cover 03
    SHIFT6m - Remove the back cover 04

    The backcover of the SHIFT6m is not glued or screwed and can be removed without tools.

    However, you can also use a plectrum to loosen the clips along the entire edge.

    1. Use a plectrum or a fingernail to slide it into the small recess in the bottom left corner and pull up the backcover.
    2. Then gradually loosen all clips all around. The back cover is hooked again around the fingerprint sensor. There you have to pull a little harder to loosen the backcover.
  3. Remove the battery

    SHIFT6m - Remove the battery 01
    SHIFT6m - Remove the battery 02
    SHIFT6m - Remove the battery 03

    You can easily remove the battery by lifting it by the notch in the lower right corner and removing it from the device.

  4. Remove the display

    SHIFT6m - Remove the display 01
    SHIFT6m - Remove the display 02
    SHIFT6m - Remove the display 03
    SHIFT6m - Remove the display 04
    SHIFT6m - Remove the display 05
    SHIFT6m - Remove the display 06
    SHIFT6m - Remove the display 07
    SHIFT6m - Remove the display 08
    • 16 × 4,0 mm Torx T3
    • 2 × 4,0 mm Torx T3
    • Display connector

    The display is attached to the entire frame with many screws of the same length. On two screws there can be a small white sticker.

    1. Loosen all screws with a Torx T3 screwdriver.
    2. Then turn the SHIFT6m over and slide a plectrum or your fingernail between the plastic frame and the display.
    3. Slide around the entire display once to gradually release it.

    The display is connected to the motherboard with a long flex cable.

    You can also keep the display connected for the following steps. In our case, we also disconnect the display connector from our device to prevent accidental damage to the flex cable during the repair process.

    1. Carefully fold the display down and place it on the frame.
    2. Loosen the two screws on the cover plate above the display contact.
    3. Then you can carefully loosen the plug of the display with a plastic spudger and finally put the display aside.
  5. The right tools for your repair

    With the right tools, you will succeed in any repair. In our store you will find a large selection of professional quality tools.
  6. Remove the camera

    SHIFT6m - Remove the camera 01
    SHIFT6m - Remove the camera 02
    SHIFT6m - Remove the camera 03
    SHIFT6m - Remove the camera 04
    SHIFT6m - Remove the camera 05
    • Camera Connector

    We have removed the mainboard from our device. But you don't have to do that to replace the camera.

    1. Carefully loosen the connector of the main camera with the Supdger.
    2. Take out the camera and remove the tape so you can attach it to the new camera right away.
  7. Install the new camera

    SHIFT6m - Install the new camera 01
    SHIFT6m - Install the new camera 02
    SHIFT6m - Install the new camera 03
    SHIFT6m - Install the new camera 04
    SHIFT6m - Install the new camera 05
    SHIFT6m - Install the new camera 06
    • Camera Connector
    1. Place the new camera in the opening of the motherboard.
    2. Connect the connector.
    3. Attach the tape that fixes the camera to the motherboard.
  8. Install the display

    SHIFT6m - Install the display 01
    SHIFT6m - Install the display 02
    SHIFT6m - Install the display 03
    SHIFT6m - Install the display 04
    SHIFT6m - Install the display 05
    SHIFT6m - Install the display 06
    • Display connector
    • 2 × 4,0 mm Torx T3
    • 16 × 4,0 mm Torx T3
    1. Place the display on the frame and position the display connector over its contact on the motherboard.
    2. Carefully push the connector down.

    The connector should engage directly with a slight click. If this does not work immediately, do not try to push the connector down with force. Reposition the connector and try again.

    1. Put on the silver cover and screw it in place.
    2. Flip the display over and press it all around until it sits correctly in the frame.
    3. Then reinstall all screws.
  9. Insert the battery

    SHIFT6m - Insert the battery 01
    SHIFT6m - Insert the battery 02
    SHIFT6m - Insert the battery 03

    Put the battery back in its place.

  10. Attach the back cover

    SHIFT6m - Attach the back cover 01
    SHIFT6m - Attach the back cover 02
    SHIFT6m - Attach the back cover 03
    SHIFT6m - Attach the back cover 04

    Put the back cover back on.

    1. The back cover has clips on the edge and around the opening of the fingerprint sensor.
    2. Press the backcover everywhere until it fits properly.
Ø 0 (0 Ratings)

Bewerte unsere Anleitung

Hat dir unsere Anleitung weitergeholfen? Wir sind auf deine Beurteilung gespannt.

Submit rating

Submit rating

How did you like this repair guide?


Similar guides

You might also be interested in these guides.

Get in touch with iDoc

Please contact our customer service for any questions about iDoc's products and services.

  • Send a message

    If you have a question about a guide or want to give us general feedback, just use our contact form

    Write a message
  • Free shipping

    From a minimum order value of 39.00 € your order will be shipped free of charge within Germany.

  • Call iDoc

    If you have any questions about our guides or services, call us from Monday to Friday, 10:00 a.m. to 6:00 p.m.

    +49 30 200 514 455
  • 5 star service

    We offer top quality and service. Our customers confirm this as well.

    Show reviews

Profi-Insights & Tipps für deine erfolgreiche Handy-Reparatur

iDoc schenkt dir den ultimativen Reparatur-Guide GUIDE GRATIS ANFORDERN

Profi-Insights & Tipps für deine erfolgreiche Handy-Reparatur

iDoc schenkt dir den ultimativen Reparatur-Guide GUIDE GRATIS ANFORDERN