The vibration motor isn’t working.

In this repair guide, we show you how to replace your Samsung Galaxy S6 Edge’s defective vibration motor on your own. You need this repair if your phone doesn’t vibrate or only barely vibrates.

Required tools

  • Heat gun

    Heat gun

    You can use a heat gun to heat parts that are glued on so they’re easier to remove. In most cases, you can also use a hairdryer.

    from €15.99 on Amazon
  • Menda ESD Spudger

    Menda ESD Spudger

    You need a flat plastic prying tool to disconnect the various plugs and connectors.

    from €26.38 on Amazon
  • Steel Laboratory Spatula

    Steel Laboratory Spatula

    You need a flat and sturdy prying tool to disconnect glued parts.

    on Amazon
  • Phillips PH00 screwdriver

    Phillips PH00 screwdriver

    You need the right screwdriver for removing PH00 screws.

    from €10.84 on Amazon
Show all replacement parts for the Galaxy S6 Edge 

Getting started with the repair of your Galaxy S6 Edge

If you get stuck or have questions, you can post a comment. We’d be happy to help.

11 steps
  1. Removing the back cover

    Galaxy S6 Edge - Removing the back cover 01
    Galaxy S6 Edge - Removing the back cover 02
    1. The back of the Samsung Galaxy S6 Edge’s enclosure is glued firmly in place. To detach it, you have to constantly heat it with a heat gun so the glue will soften. Then you have to insert a plastic pick into the gap between the frame and the glass to detach the adhesive.
    2. The gap between the aluminum frame and the glass is very small. We recommend that you use a very flat, sturdy object to get between them.
    3. Carefully lift the back cover while using a suction cup.
    4. As soon as a little gap opens up, use the plastic pick to avoid damaging the aluminum.
  2. Inserting the pick

    Galaxy S6 Edge - Inserting the pick 01
    Galaxy S6 Edge - Inserting the pick 02
    1. You should only insert the pick about two or three millimeters between the back cover and the frame to prevent damage inside the enclosure.
      The back cover is painted on the inside. Remove any adhesive residue carefully to avoid scratches or cracks.
    2. The back cover is glued to the entire outer edge of the Galaxy S6 Edge. Move the pick once around the entire phone.
    3. Once you’ve detached all the glue, you can carefully lift the back cover.
  3. Removing the midframe

    Galaxy S6 Edge - Removing the midframe 01
    Galaxy S6 Edge - Removing the midframe 02
    Galaxy S6 Edge - Removing the midframe 03
    Galaxy S6 Edge - Removing the midframe 04
    Galaxy S6 Edge - Removing the midframe 05
    1. Remove the 13 Phillips screws that hold the plastic cover in place (see figure 1)..
      13 x 3.3 mm Phillips screws
    2. Take out the SIM card tray.
    3. Now lift the charging pad for wireless charging. It’s lightly glued to the midframe.
    4. In order to remove the midframe, you have to carefully push down the battery and the rest of the smartphone. Use your other hand to push up the frame. If it doesn’t move, carefully insert a pick between the display and the frame, and press it upward.
  4. Removing the front camera

    Galaxy S6 Edge - Removing the front camera 01
    Galaxy S6 Edge - Removing the front camera 02
    1. Place the pointed tip of the spudger very slightly below the contact and lift it up. Make sure you don’t break off the resistors that are soldered onto the logic board.
    2. Now you can disconnect the front camera connector. Be very careful.
  5. Removing the logic board

    1. Before you can remove the logic board, you have to unscrew two black screws on the dock connector.
      2 x 3.3 mm Phillips screws
    2. Then you have to disconnect the following contacts. Place the pointed tip of the spudger very slightly below the contacts and lift them up.
      Battery
      Display (connect the new display and test all the functions)
      Earpiece
      Home button
    3. Then insert the spudger below the dock connector cable set, which is lightly glued on, and lift it up. A sensor is also lightly glued on.
    4. Now you can remove the logic board with the dock connector connected.

    There's a small plastic pin in the opening of the SIM tray. Make sure it doesn't fall out.

  6. The right tools for your repair

    With the right tools, you will succeed in any repair. In our store you will find a large selection of professional quality tools.
    VIEW NOW
  7. Removing the vibration motor

    Galaxy S6 Edge - Removing the vibration motor 01
    Galaxy S6 Edge - Removing the vibration motor 02
    1. Now remove the vibration motor. Insert a sharp object below the vibration motor, which is lightly glued in place, and lift it carefully. The copper contact point is also lightly glued on.
    2. Make sure it doesn’t tear. If you still can’t detach the vibration motor, you can use a heat gun to warm it slightly and soften the glue.
    3. Remove the vibration motor.
  8. Installing the vibration motor

    Galaxy S6 Edge - Installing the vibration motor 01
    1. Now put the vibration motor back in the appropriate position. The old glue is usually enough to hold it. Press it on firmly.
    2. If the vibration motor is too loose, use new glue. If the motor isn’t attached securely enough, your phone’s vibration will be weaker.
  9. Installing the logic board

    Galaxy S6 Edge - Installing the logic board 01
    Galaxy S6 Edge - Installing the logic board 02
    Galaxy S6 Edge - Installing the logic board 03
    1. Now put the logic board back in the frame. Start with the dock connector connected to the logic board.
    2. Once it’s fitted correctly, you can install the rest of the logic board. Make sure the cables don’t get under the logic board. Use the picture to check whether your logic board is positioned correctly.
    3. Now reconnect all the connectors:
      Battery
      Display
      Earpiece
      Home button
    4. Now fasten the black screws for the dock connector.
      2 x 3.3 mm Phillips screws
  10. Installing the front camera

    Galaxy S6 Edge - Installing the front camera 01
    1. Now put the front camera in the original location.
    2. Then connect the connector to the logic board.
  11. Connecting the frame components

    Galaxy S6 Edge - Connecting the frame components 01
    Galaxy S6 Edge - Connecting the frame components 02
    1. Attach the outer frame to the main component again. Start at the dock connector and firmly press the two frame components together.
    2. Then screw them together.
      13 x 3.3 mm Phillips screws
  12. Attaching the back cover

    Galaxy S6 Edge - Attaching the back cover 01
    1. As a last step, you have to attach the back cover again.
    2. The old glue is usually still sticky enough.
    3. Put the back cover back on, heat it slightly and then use a little force to press it onto the smartphone for a while.
Ø 5 (28 Ratings)

Bewerte unsere Anleitung

Hat dir unsere Anleitung weitergeholfen? Wir sind auf deine Beurteilung gespannt.

Submit rating

Submit rating

How did you like this repair guide?

Exceptional

Similar guides

You might also be interested in these guides.

You might be interested in

Get in touch with iDoc

Please contact our customer service for any questions about iDoc's products and services.

  • Send a message

    If you have a question about a guide or want to give us general feedback, just use our contact form

    Write a message
  • Free shipping

    From a minimum order value of 79.00 € your order will be shipped free of charge within Germany.

  • Call iDoc

    If you have any questions about our guides or services, call us from Monday to Friday, 10:00 a.m. to 6:00 p.m.

    +49 30 200 514 455
  • 5 star service

    We offer top quality and service. Our customers confirm this as well.

    Show reviews

Profi-Insights & Tipps für deine erfolgreiche Handy-Reparatur

iDoc schenkt dir den ultimativen Reparatur-Guide GUIDE GRATIS ANFORDERN

Profi-Insights & Tipps für deine erfolgreiche Handy-Reparatur

iDoc schenkt dir den ultimativen Reparatur-Guide GUIDE GRATIS ANFORDERN