LG G7 ThinQ Screen replacement repair guide

Replace the screen of your LG G7 ThinQ yourself

  • G7 ThinQ
  • 19 Steps
  • Medium
  • 45 min.
Go to the guide

Introduction

Is the screen of your LG G7 ThinQ cracked or is the touchscreen not working properly anymore? With our instructions you can easily repair your LG G7 ThinQ yourself!

During this repair, we replace the entire display unit including the frame, not just the broken screen.


The repair is a bit more difficult because the LG G7 ThinQ has to be opened via the glass back cover.


Make a backup before the repair, use a clean work surface and take your time. If you are stuck at any point, simply contact our live chat or write a comment at the end of the guide.

Required tools

  • Heat gun

    Heat gun

    You can use a heat gun to heat parts that are glued on so they’re easier to remove. In most cases, you can also use a hairdryer.

    from €14.99 on Amazon
  • iPlastix

    iPlastix

    Dein Smartphone zu öffnen kann eine sehr empfindliche Angelegenheit sein. Die Klinge des biegsamen aber stabilen iPlastix hat eine Dicke von nur 0,15 mm, sodass es auch in den kleinsten Spalten reinpasst, beispielsweise zwischen dem Display und dem Rahmen oder unter dem Logicboard. Das praktische iPlastix ist aus biegsamem Kunststoff und liegt gut in der Hand. Damit ist es der perfekte Helfer bei jeder Smartphone-Reparatur.

    €9.00 at the iDoc store
  • iSclack

    iSclack

    Dein iPhone oder iPad kannst du erst reparieren, wenn du das Gerät aufkriegst. Das klingt vielleicht einfach, kann aber ein sehr heikler und komplizierter Vorgang sein. Wie soll man das Ganze festhalten, und wie kriegt man die unterschiedlichen Teile auseinander? Wie macht man das, ohne noch etwas kaputtzumachen? Mit dem praktischen Öffnungstool iSclack geht’s viel einfacher und sicherer. Zwei gegenüberliegende Saufnäpfe greifen Display und Rückschale fest. Mit dem zangenartigen Griff braucht man nur eine Hand, um die Beiden zu bewegen. Die beigelegten Abdeckfolien ermöglichen die Benutzung auch beim zersplitterten Display.

    €15.00 at the iDoc store
  • Tweezers

    Tweezers

    We recommend using tweezers to remove screws and various small parts from your device.

    €16.00 at the iDoc store
  • Plastic prying tool

    Plastic prying tool

    You need a flat plastic prying tool to disconnect the various plugs and connectors.

    €1.00 at the iDoc store
  • Suction cup

    Suction cup

    A suction cup is perfect for lifting smooth surfaces such as displays or rear glass panels.

    €2.00 at the iDoc store
  • Phillips PH00 screwdriver

    Phillips PH00 screwdriver

    You need the right screwdriver for removing PH00 screws.

    €10.00 at the iDoc store

Required replacement part

  • LG G7 ThinQ Display Grau / New Platinum Gray

    LG G7 ThinQ Display Grau / New Platinum Gray

    Dein LG G7 ThinQ ist dir aus den Händen gefallen. Hoffnungsvoll hast du es aufgehoben, aufs Display geschaut – leider ist das Glas gebrochen. Verständlicherweise ist dieses Missgeschick total ärgerlich. Zum Glück haben wir eine Lösung für dich parat: ein neues LCD inklusive Rahmen für dein LG G7 ThinQ. Das Ersatzteil ist original von LG und kommt als komplette Einheit. Was das bedeutet? Alle Tasten sowie die Hörmuschel, der Kopfhörerausgang und der USB Typ-C Anschluss sind im Rahmen bereits enthalten. Auch die Klebeflächen, die den Akku an seiner Stelle halten, sind schon vormontiert. Dadurch wird der Austausch deines Ersatz-Displays stark vereinfacht. So kannst du dein LG G7 ThinQ schon bald wieder so nutzen, wie du es gewohnt bist: Ganz ohne Spider-App!

    €159.00 at the iDoc store
Show all replacement parts for the G7 ThinQ 

Replacement parts and tools for this repair

Our tools plus the right spare part help you fix your device easily.

LG G7 ThinQ Display Grau / New Platinum Gray

Dein LG G7 ThinQ ist dir aus den Händen gefallen. Hoffnungsvoll hast du es aufgehoben, aufs Display geschaut – leider ist das...

Werkzeugset Samsung

Ganz gleich, welches Problem dein Handy hat - mit unserem Werkzeugset kannst du es bestimmt beheben. Dieses Reparaturset umfasst jeweils einen...

together for €208.00

LG G7 ThinQ Display Schwarz / New Aurora Black

Dein LG G7 ThinQ ist dir aus den Händen gefallen. Hoffnungsvoll hast du es aufgehoben, aufs Display geschaut – leider ist das...

Werkzeugset Samsung

Ganz gleich, welches Problem dein Handy hat - mit unserem Werkzeugset kannst du es bestimmt beheben. Dieses Reparaturset umfasst jeweils einen...

together for €208.00

Getting started

If you get stuck or have questions, you can post a comment for each step. We’d be happy to help.

19 steps
  1. Switching off the LG G7 ThinQ

    G7 ThinQ - Switching off the LG G7 ThinQ 01
    G7 ThinQ - Switching off the LG G7 ThinQ 02
    G7 ThinQ - Switching off the LG G7 ThinQ 03
    G7 ThinQ - Switching off the LG G7 ThinQ 04
    1. Turn off your device by holding down the power button on the side until the “Power off” option appears.
    2. Tap to confirm and wait until the screen goes black.
  2. Removing the back cover

    G7 ThinQ - Removing the back cover 01
    G7 ThinQ - Removing the back cover 02
    G7 ThinQ - Removing the back cover 03
    G7 ThinQ - Removing the back cover 04
    G7 ThinQ - Removing the back cover 05
    G7 ThinQ - Removing the back cover 06
    G7 ThinQ - Removing the back cover 07
    1. The back cover’s heavily glued to the chassis. Heat the device evenly with hot air to soften the glue. A temperature of 60 - 80°C should be sufficient. As a rule of thumb, you should still be able to touch your device without it being uncomfortably hot.
    2. The easiest way to loosen the back cover is to use a flat and flexible tool such as the iPlastix or iFlex. You will also need several picks to unstick the back cover all around.
    3. Heat the spot where you start and place a flat tool between the back cover and the frame.
    4. Use a suction cup to lift the glass if you can't find a place to insert your tool.
    5. With the iSclack, you can easily lift the back cover and then use a flat tool to loosen the glue. Put both suction cups on the display and the backcover and press the lever of the tool together like a pair of pliers.

    The iPlastix is made of plastic, so it won't scratch the device. On the other hand, it's very soft and tricky to insert. The iFlex makes it easier to get into the gap between the glass and the frame because it's made of very thin, stable metal. But it also makes it easier to scratch the frame of your device.

    Be extra careful, the back cover can break very easily. If necessary, apply the heat several times and try again. Removing the back cover might take half an hour. Take a little more time and work carefully to make sure you don't break anything.

    1. Once the tool is inserted, stick a pick into the gap to keep it open. Then run the tool around the entire edge to gradually loosen the glue.
    2. Then heat the next part and insert the picks one by one.
    3. Once the rear glass is unglued, you can lift it off. There's no cable attached.
  3. Removing the midframe

    G7 ThinQ - Removing the midframe 01
    G7 ThinQ - Removing the midframe 02
    G7 ThinQ - Removing the midframe 03
    G7 ThinQ - Removing the midframe 04
    G7 ThinQ - Removing the midframe 05
    • 7 × 3,5 mm Phillips
    1. Loosen the Phillips screws that secure the cover. The wireless charging coil and NFC antenna are attached to the plastic cover.
    2. The cover is hooked into the housing. Lever with a tool under the plastic frame and lift the frame upwards.
    3. Now you can remove the plastic cover together with the coil.
  4. Disconnecting the battery

    G7 ThinQ - Disconnecting the battery 01
    G7 ThinQ - Disconnecting the battery 02
    G7 ThinQ - Disconnecting the battery 03
    • Battery Connector
    1. Using the spudger, carefully disconnect the battery contact from the motherboard.

    Always lever from a side where there are no small components on the motherboard. This avoids unintentional damage to capacitors or ICs.

  5. Removing the speaker

    G7 ThinQ - Removing the speaker 01
    G7 ThinQ - Removing the speaker 02
    G7 ThinQ - Removing the speaker 03
    G7 ThinQ - Removing the speaker 04
    • 7 × 3,5 mm Phillips
    1. Loosen the Phillips screws that secure the speaker and then remove it.
    2. You can easily release the speaker by pulling it up at the top with your fingernail.
  6. Removing the SIM card tray

    G7 ThinQ - Removing the SIM card tray 01
    G7 ThinQ - Removing the SIM card tray 02
    1. Slide a SIM tool into the hole in the SIM tray.
    2. Take the SIM slider out of the device.
  7. Removing the mainboard

    G7 ThinQ - Removing the mainboard 01
    G7 ThinQ - Removing the mainboard 02
    G7 ThinQ - Removing the mainboard 03
    G7 ThinQ - Removing the mainboard 04
    G7 ThinQ - Removing the mainboard 05
    G7 ThinQ - Removing the mainboard 06
    G7 ThinQ - Removing the mainboard 07
    • Display connector
    • Camera connector
    • Antenna connector
    • USB connector
    1. First carefully remove the highlighted connectors from the main board using a spudger. They connect the front camera, the screen and various antennas.
    2. Another contact is located on the lower side of the main board and cannot be separated directly.
    3. Use the Supdger to carefully lever up the bottom side of the board until you notice the connector coming loose.
    4. Now you can carefully remove the motherboard. Make sure it doesn’t get caught on the connectors you already disconnected.
    5. Then set the board aside in a safe place.
  8. Removing the battery

    G7 ThinQ - Removing the battery 01
    G7 ThinQ - Removing the battery 02
    G7 ThinQ - Removing the battery 03
    G7 ThinQ - Removing the battery 04
    G7 ThinQ - Removing the battery 05
    G7 ThinQ - Removing the battery 06

    The battery is strongly glued in place, so you should use hot air again to loosen the glue.

    Never heat the battery directly and avoid deforming the battery too much.

    1. Heat the adhesive on the back of the battery by heating the display.
    2. We recommend using a flat tool, such as the iPlastix, to get under the battery all around and carefully lever it.
    3. If the adhesive is loosened everywhere, lift the battery and remove it from the device.

    Be careful not to damage the battery. Take your time again and heat the glue several times.

  9. Removing the front camera and the vibration motor

    G7 ThinQ - Removing the front camera and the vibration motor 01
    G7 ThinQ - Removing the front camera and the vibration motor 02
    G7 ThinQ - Removing the front camera and the vibration motor 03
    G7 ThinQ - Removing the front camera and the vibration motor 04
    G7 ThinQ - Removing the front camera and the vibration motor 05

    Finally you have to remove the front camera and the vibration motor to install them in the new replacement display.

    1. Lever the camera out of its opening and remove it.
    2. The vibration motor is glued to the enclosure. Carefully detach the motor by inserting your tool between the enclosure and the motor.

    Do not lever on the side with the golden contacts, as these can easily break off.

  10. Preparing the new display

    G7 ThinQ - Preparing the new display 01
    G7 ThinQ - Preparing the new display 02
    1. Now take the new display and compare it to the old one. If necessary, you have to reuse some gaskets or holders.
    2. Remove the backing films from the sticker surfaces, so you can attach the front camera or the battery later on.
  11. Installung the front camera and the vibration motor

    G7 ThinQ - Installung the front camera and the vibration motor 01
    G7 ThinQ - Installung the front camera and the vibration motor 02

    In the following pictures you can see the old display again. We did not install a new display for our repair guide, because our device had no defect. But the procedure is the same.

    1. Put the front camera in its opening. Make sure that there is no protective film on the inside of the display.
    2. Put the vibration motor in the little round opening on side of the case.
    3. Use your fingers to press the motor firmly into place.
  12. Installing the battery

    G7 ThinQ - Installing the battery 01
    G7 ThinQ - Installing the battery 02
    1. Put the battery in the display unit.
    2. Press the battery into the frame firmly so the glue will stick better.

    You can also wait until all the other components are installed before inserting the battery. This makes it easier to insert the main board in the next step.

  13. Installing the main board

    G7 ThinQ - Installing the main board 01
    G7 ThinQ - Installing the main board 02
    G7 ThinQ - Installing the main board 03
    G7 ThinQ - Installing the main board 04
    G7 ThinQ - Installing the main board 05
    • USB connector
    • Display connector
    • Camera connector
    • Antenna connector
    1. Take the motherboard and carefully insert it into the device. Be careful not to pinch any cables. Bend all connectors to the side.
    2. When the mainboard is positioned correctly, you can connect the connector on the bottom by pushing it down.

    The connector should click into place directly. Do not force the contact if this does not work right away. First check that the mainboard is correctly positioned.

    1. Then connect all the other connectors.


  14. Installing the SIM card tray

    G7 ThinQ - Installing the SIM card tray 01
    G7 ThinQ - Installing the SIM card tray 02
    1. Insert the SIM card holder. If it's stuck, don't push it in with force. In this case check if the mainboard is correctly positioned.
  15. Installing the speaker

    G7 ThinQ - Installing the speaker 01
    G7 ThinQ - Installing the speaker 02
    G7 ThinQ - Installing the speaker 03
    • 7 × 3,5 mm Phillips
    1. Then place the speaker back over the USB port, press it in and screw it tight.
    2. Make sure it's latched in at the bottom.
  16. Connecting the battery

    G7 ThinQ - Connecting the battery 01
    G7 ThinQ - Connecting the battery 02
    G7 ThinQ - Connecting the battery 03
    • Battery Connector
    1. Connect the battery to the mainboard. Press the contact onto the connection on the motherboard until you hear it click into place.
  17. Installing the midframe

    G7 ThinQ - Installing the midframe 01
    G7 ThinQ - Installing the midframe 02
    G7 ThinQ - Installing the midframe 03
    G7 ThinQ - Installing the midframe 04
    • 7 × 3,5 mm Phillips
    1. Put the cover with the antenna back in the enclosure after sliding it under the speaker at the bottom.
    2. Then press the cover with your fingers until it clicks gently into place.
    3. Fasten the phillips screws.
  18. Testing the LG G7 ThinQ

    G7 ThinQ - Testing the LG G7 ThinQ 01
    G7 ThinQ - Testing the LG G7 ThinQ 02
    G7 ThinQ - Testing the LG G7 ThinQ 03
    G7 ThinQ - Testing the LG G7 ThinQ 04
    1. Turn on your device and test it before you finally close it.
    2. Drag any app across the entire screen. Drag the app once around the entire border and then in a zigzag across the screen. The app should always follow your finger.
    3. Then test the display brightness by dragging the brightness slider to minimum and maximum.

    Test especially all functions of the part you replaced.

  19. Attaching the backcover

    G7 ThinQ - Attaching the backcover 01
    G7 ThinQ - Attaching the backcover 02
    G7 ThinQ - Attaching the backcover 03

    If the adhesive on the back cover is still intact, you can seal your device without using a new adhesive frame.

    1. Put the back cover back in its original position.
    2. Press the back cover on all over so the glue will stick.

    You can also heat your device with hot air and then clamp it or weight it down with a couple of books so the glue will stick better.

    If you install a new back cover, now remove the last protective films from the adhesive surfaces.


    Please also note that after a repair the device is no longer 100% waterproof.
Ø 0 (0 Bewertungen)

Bewerte unsere Anleitung

Hat dir unsere Anleitung weitergeholfen? Wir sind auf deine Beurteilung gespannt.

Bewertung abgeben

Bewertung abgeben

Wie findest du unsere Reparatur-Anleitung G7 ThinQ Replace the screen?

Exzellent

Similar guides

You might also be interested in these guides.

You might be interested in

Get in touch with iDoc

Please contact our customer service for any questions about iDoc's products and services.

  • Send a message

    If you have a question about a guide or want to give us general feedback, just use our contact form

    Write a message
  • Free shipping

    From a minimum order value of 39.00 € your order will be shipped free of charge within Germany.

  • Call iDoc

    If you have any questions about our guides or services, call us from Monday to Friday, 10:00 a.m. to 6:00 p.m.

    +49 30 200 514 455
  • 5 star service

    We offer top quality and service. Our customers confirm this as well.

    Show reviews