The rear-facing camera isn’t working

In this guide, we show you how to replace your iPhone 6 Plus’ defective rear camera on your own. You need this repair if the rear camera isn’t working, your pictures are blurry, or the camera doesn’t focus.

Required tools

  • For storing screws

    For storing screws

    We recommend storing your screws so you don’t mix up the various screws and small parts.

    from €10.99 on Amazon
  • Tweezers

    Tweezers

    We recommend using tweezers to remove screws and various small parts from your device.

    on Amazon
  • Pick Set

    Pick Set

    You need a flat but stable tool such as a pick to pry out parts that are glued in place.

    from €14.99 on Amazon
  • Plastic prying tool

    Plastic prying tool

    You need a flat plastic prying tool to disconnect the various plugs and connectors.

    from €14.99 on Amazon
  • Steel Laboratory Spatula

    Steel Laboratory Spatula

    You need a flat and sturdy prying tool to disconnect glued parts.

    on Amazon
  • Pentalobe PL1 screwdriver

    Pentalobe PL1 screwdriver

    You need the right screwdriver for removing pentalobe PL1 screws.

    on Amazon
  • Phillips PH00 screwdriver

    Phillips PH00 screwdriver

    You need the right screwdriver for removing PH00 screws.

    from €10.84 on Amazon

Required replacement part

Show all replacement parts for the iPhone 6 Plus 

Getting started with the repair of your iPhone 6 Plus

If you get stuck or have questions, you can post a comment. We’d be happy to help.

11 steps
  1. Turning off your Device

    iPhone 6 Plus - Turning off your Device 01
    iPhone 6 Plus - Turning off your Device 02
    1. Turn your iPhone off completely to avoid damaging it during the repair. Press the standby button for about three seconds until the slider appears.
    2. Wipe it from left to right. Now your iPhone will shut down completely, which can take about ten seconds.
  2. Removing the enclosure screws

    iPhone 6 Plus - Removing the enclosure screws 01
    iPhone 6 Plus - Removing the enclosure screws 02
    1. You need a pentalobe screwdriver to open the iPhone 6 Plus.
    2. Remove the two pentalobe screws at the bottom of the enclosure. They are located to the right and left of the Lightning connector. Put the screws in the same container.
      2 x 3.8 mm pentalobe screw
  3. Lifting the display

    iPhone 6 Plus - Lifting the display 01
    iPhone 6 Plus - Lifting the display 02
    iPhone 6 Plus - Lifting the display 03
    1. Put your iPhone 6 Plus on a soft, clean surface to avoid scratching the back.
    2. To lift the front panel, you need a suction cup and a hard plastic pick. If the screen is severely cracked, cover all of it with packing tape before you continue.
    3. Place the suction cup over the Home button (if possible) or next to it (see figure 1). While lifting the screen with the suction cup, insert the hard plastic pick between the aluminum frame and the display frame and press down the aluminum frame. Also use the hard plastic pick to raise the screen (see figure 2). This usually takes several attempts.
    4. As soon as you can lift the screen a few millimeters, you have to carefully work your way around the outside until it’s loosened on both sides (see figure 3).
  4. Disconnecting the battery connector

    iPhone 6 Plus - Disconnecting the battery connector 01
    iPhone 6 Plus - Disconnecting the battery connector 02
    iPhone 6 Plus - Disconnecting the battery connector 03
    1. Use a Phillips screwdriver to remove the Phillips screws on the battery connector (see figure 1). Then lift the cover (see figure 2). Put all the parts in the same container.
      1 x 3.2 mm Phillips screw
      1 x 2.3 mm Phillips screw
    2. Now carefully lift the battery connector by inserting the pointed tip of the ESD spudger slightly below the connector (see figure 3). If you don’t have a spudger, you can also try using your fingernail.
  5. Disconnecting the connectors

    iPhone 6 Plus - Disconnecting the connectors 01
    iPhone 6 Plus - Disconnecting the connectors 02
    1. First remove the five Phillips screws from the silver cover (see figure 1). Put the screws in the same container. Then lift the cover to remove it.
      1 x 1.6 mm Phillips screw
      3 x 1.2 mm Phillips screw
      1 x 2.9 mm Phillips screw
    2. Disconnect the following four overlapping connectors (see figure 2) in the order shown below. Be very careful. Place the pointed tip of the spudger very slightly below the contact and lift it up.
      Front camera/sensor/earpiece/ambient microphone
      Touch ID cable
      LCD
      Touchscreen
  6. The right tools for your repair

    With the right tools, you will succeed in any repair. In our store you will find a large selection of professional quality tools.
    VIEW NOW
  7. Removing the iSight camera

    iPhone 6 Plus - Removing the iSight camera 01
    iPhone 6 Plus - Removing the iSight camera 02
    iPhone 6 Plus - Removing the iSight camera 03
    iPhone 6 Plus - Removing the iSight camera 04
    iPhone 6 Plus - Removing the iSight camera 05
    iPhone 6 Plus - Removing the iSight camera 06
    1. First uncover the upper screw in the camera cover. It’s below a piece of black tape. (See figure 1).
    2. Unscrew the two Phillips screws from the camera cover (see figure 2).
      1 x 1.6 mm Phillips screw
      1 x 2.1 mm Phillips screw
    3. Now remove the silver camera cover (see figure 3).
    4. Then disconnect the camera connector by placing the pointed tip of the spudger very slightly below the contact and lifting it up (see figure 4).
    5. The camera is fitted very securely in the enclosure. You may have to use the spudger to remove the camera (see figure 5).
    6. Now lift the camera out of the phone (see figure 6).
  8. Connecting the camera

    iPhone 6 Plus - Connecting the camera 01
    iPhone 6 Plus - Connecting the camera 02
    iPhone 6 Plus - Connecting the camera 03
    iPhone 6 Plus - Connecting the camera 04
    1. Put the camera back in its original position and connect the camera’s connection cable (see figure 1).
    2. Now install the camera cover (see figure 2) and screw it in place (see figure 3).
      1 x 1.6 mm Phillips screw
      1 x 2.1 mm Phillips screw
    3. Now put the small black sticker back on (see figure 4).
  9. Connecting the display

    iPhone 6 Plus - Connecting the display 01
    iPhone 6 Plus - Connecting the display 02
    1. Reattach the connectors (see figure 1). Connecting the LCD connector generally takes a few tries. Be very careful to avoid bending the connector.
      Front camera/sensor/earpiece/ambient microphone
      Touch ID cable
      LCD
      Touchscreen
    2. Start your iPhone as soon as the connectors are securely attached. Check the function of the LCD, touchscreen, proximity sensor, front camera and earpiece.
      If the connectors aren’t connected properly, stripes will appear on the display or parts of the touchscreen won’t work.
    3. Now attach the cover and screw it in place (see figure 2).
      1 x 1.6 mm Phillips screw
      3 x 1.2 mm Phillips screw
      1 x 2.9 mm Phillips screw
  10. Installing the battery

    iPhone 6 Plus - Installing the battery 01
    iPhone 6 Plus - Installing the battery 02
    iPhone 6 Plus - Installing the battery 03
    1. Attach new adhesive strips below the battery. Otherwise, the battery will have too much room and move around
    2. Now put the battery back in the iPhone and connect the connector (see figure 1).
    3. Put on the silver cover and screw it in place (see figure 2).
      1 x 3.2 mm Phillips screw
      1 x 2.3 mm Phillips screw
  11. Attaching the display

    iPhone 6 Plus - Attaching the display 01
    1. Then carefully fold down the screen. Make sure that the edge on the upper part of the screen where the cables are clicks into place properly. Now carefully push the screen on toward the Home button until it is properly installed in the frame.
  12. Fastening the enclosure screws

    iPhone 6 Plus - Fastening the enclosure screws 01
    1. Now screw in the two pentalobe screws at the bottom of the enclosure.
      2 x 3.8 mm pentalobe screws
Ø 4.8 (16 Ratings)

Bewerte unsere Anleitung

Hat dir unsere Anleitung weitergeholfen? Wir sind auf deine Beurteilung gespannt.

Submit rating

Submit rating

How did you like this repair guide?

Exceptional

Similar guides

You might also be interested in these guides.

You might be interested in

Get in touch with iDoc

Please contact our customer service for any questions about iDoc's products and services.

  • Send a message

    If you have a question about a guide or want to give us general feedback, just use our contact form

    Write a message
  • Free shipping

    From a minimum order value of 79.00 € your order will be shipped free of charge within Germany.

  • Call iDoc

    If you have any questions about our guides or services, call us from Monday to Friday, 10:00 a.m. to 6:00 p.m.

    +49 30 200 514 455
  • 5 star service

    We offer top quality and service. Our customers confirm this as well.

    Show reviews

Profi-Insights & Tipps für deine erfolgreiche Handy-Reparatur

iDoc schenkt dir den ultimativen Reparatur-Guide GUIDE GRATIS ANFORDERN

Profi-Insights & Tipps für deine erfolgreiche Handy-Reparatur

iDoc schenkt dir den ultimativen Reparatur-Guide GUIDE GRATIS ANFORDERN