Samsung Galaxy S7 Edge - Replacing the display

The screen is broken or remains black.

  • Galaxy S7 Edge
  • 36 Steps
  • Difficult
  • 60 min.
Go to the guide

Introduction

In this repair guide, we show you how to replace your Galaxy S7 Edge’s defective display unit on your own. You need this repair if the glass is cracked, the touchscreen no longer responds to touch, or the OLED remains black or flickers.

Required tools

  • Flache Plektren

    Flache Plektren

    You need a very flat tool such as a flat pick to pry out parts that are glued in place.

    €1.00 at the iDoc store
  • Heat gun

    Heat gun

    You can use a heat gun to heat parts that are glued on so they’re easier to remove. In most cases, you can also use a hairdryer.

    from €14.99 on Amazon
  • For storing screws

    For storing screws

    We recommend storing your screws so you don’t mix up the various screws and small parts.

    €10.00 at the iDoc store
  • Tweezers

    Tweezers

    We recommend using tweezers to remove screws and various small parts from your device.

    €16.00 at the iDoc store
  • Plastic prying tool

    Plastic prying tool

    You need a flat plastic prying tool to disconnect the various plugs and connectors.

    €1.00 at the iDoc store
  • Suction cup

    Suction cup

    A suction cup is perfect for lifting smooth surfaces such as displays or rear glass panels.

    €2.00 at the iDoc store
  • Phillips PH00 screwdriver

    Phillips PH00 screwdriver

    You need the right screwdriver for removing PH00 screws.

    €10.00 at the iDoc store

Required replacement part

  • Samsung Galaxy S7 Edge Display Schwarz / Black-Onyx

    Samsung Galaxy S7 Edge Display Schwarz / Black-Onyx

    Ist dir dein Smartphone runtergefallen und jetzt kannst du kaum noch etwas auf dem gebrochenen Bildschirm erkennen? Dann ist es höchste Zeit, das Display deines Galaxy S7 Edge auszutauschen. Wenn dein Displayglas zersprungen ist, der Touchscreen nicht mehr auf Berührungen reagiert, schwarz bleibt oder flackert, kann dieses neue Display-Assembly helfen. Der Homebutton mit Fingersensor und die Ladebuchse sind vormontiert. Nach dem Austausch funktioniert der Fingersensor wie am ersten Tag.

    €179.00 at the iDoc store
  • Samsung Galaxy S7 Edge Rückglaskleber

    Samsung Galaxy S7 Edge Rückglaskleber

    Nach der Reparatur deines Samsung Galaxy S7 Edge musst du nur noch das Rückglas montieren? Hier hilft dir der Kleberahmen das Backcover richtig zu befestigen. Dein Samsung Galaxy S7 wird wohl nie 100% wasserfest sein, aber mit Hilfe der Klebefolie ist das Samsung Galaxy S7 Edge besser vor Spritzwasser und Staub geschützt.

    €3.00 at the iDoc store
Show all replacement parts for the Galaxy S7 Edge 

Replacement parts and tools for this repair

Our tools plus the right spare part help you fix your device easily.

Samsung Galaxy S7 Edge Display Gold / Gold-Platinum

Ist dir dein Smartphone runtergefallen und jetzt kannst du kaum noch etwas auf dem gebrochenen Bildschirm erkennen? Dann ist es...

Werkzeugset Samsung

Ganz gleich, welches Problem dein Handy hat - mit unserem Werkzeugset kannst du es bestimmt beheben. Dieses Reparaturset umfasst jeweils einen...

together for €228.00

Samsung Galaxy S7 Edge Display Pink-Gold

Ist dir dein Smartphone runtergefallen und jetzt kannst du kaum noch etwas auf dem gebrochenen Bildschirm erkennen? Dann ist es...

Werkzeugset Samsung

Ganz gleich, welches Problem dein Handy hat - mit unserem Werkzeugset kannst du es bestimmt beheben. Dieses Reparaturset umfasst jeweils einen...

together for €228.00

Samsung Galaxy S7 Edge Display Schwarz / Black-Onyx

Ist dir dein Smartphone runtergefallen und jetzt kannst du kaum noch etwas auf dem gebrochenen Bildschirm erkennen? Dann ist es...

Werkzeugset Samsung

Ganz gleich, welches Problem dein Handy hat - mit unserem Werkzeugset kannst du es bestimmt beheben. Dieses Reparaturset umfasst jeweils einen...

together for €228.00

Samsung Galaxy S7 Edge Display Silber / Silver-Titanium

Ist dir dein Smartphone runtergefallen und jetzt kannst du kaum noch etwas auf dem gebrochenen Bildschirm erkennen? Dann ist es...

Werkzeugset Samsung

Ganz gleich, welches Problem dein Handy hat - mit unserem Werkzeugset kannst du es bestimmt beheben. Dieses Reparaturset umfasst jeweils einen...

together for €228.00

Samsung Galaxy S7 Edge Display Weiß / White-Pearl

Ist dir dein Smartphone runtergefallen und jetzt kannst du kaum noch etwas auf dem gebrochenen Bildschirm erkennen? Dann ist es...

Werkzeugset Samsung

Ganz gleich, welches Problem dein Handy hat - mit unserem Werkzeugset kannst du es bestimmt beheben. Dieses Reparaturset umfasst jeweils einen...

together for €228.00

Getting started

If you get stuck or have questions, you can post a comment for each step. We’d be happy to help.

36 steps
  1. Switching off your device

    Galaxy S7 Edge - Switching off your device 01
    Galaxy S7 Edge - Switching off your device 02
    1. Turn off your device by holding down the power button until the “Power off” option appears.
    2. Use your finger to confirm that you want to shut down your Galaxy S7 Edge and wait until the screen goes blank.
  2. Removing the SIM and microSD cards

    Galaxy S7 Edge - Removing the SIM and microSD cards 01
    Galaxy S7 Edge - Removing the SIM and microSD cards 02
    Galaxy S7 Edge - Removing the SIM and microSD cards 03
    1. Use the SIM tool to eject the SIM tray from your device and then remove the tray with your fingers.
  3. Removing the back cover

    Galaxy S7 Edge - Removing the back cover 01
    Galaxy S7 Edge - Removing the back cover 02
    Galaxy S7 Edge - Removing the back cover 03
    Galaxy S7 Edge - Removing the back cover 04
    Galaxy S7 Edge - Removing the back cover 05
    1. The back cover is glued to the chassis. Remove the back cover by putting on a suction cup and pulling on it. Also use a pick to push against the frame. Heat your device with hot air beforehand so the glue will be easier to detach.
    2. As soon as a gap appears between the back cover and the chassis, you can insert the pick between the two parts.
      The back cover is painted on the inside. Remove any adhesive residue carefully to avoid scratches or cracks.
    3. Use more picks to disconnect all the corners one after the other.
    4. Remove the back cover as soon as all the glue is detached.
  4. Removing the screws

    Galaxy S7 Edge - Removing the screws 01
    Galaxy S7 Edge - Removing the screws 02
    Galaxy S7 Edge - Removing the screws 03
    • 12 × 3.3 mm PH00 Phillips screws
    1. Remove the twelve screws that hold the three antennas in place.
    2. Remove the yellow adhesive strip.
  5. Removing the upper antenna

    Galaxy S7 Edge - Removing the upper antenna 01
    Galaxy S7 Edge - Removing the upper antenna 02
    Galaxy S7 Edge - Removing the upper antenna 03
    Galaxy S7 Edge - Removing the upper antenna 04
    1. Disconnect the upper antenna from the enclosure. The antenna is hooked onto the enclosure. Start at the upper right corner.
    2. As soon as the antenna has come off on the right side, carefully pull it up in the middle so the left side will come off, too.
    3. Remove the antenna from the enclosure.
  6. Removing the middle antenna

    Galaxy S7 Edge - Removing the middle antenna 01
    Galaxy S7 Edge - Removing the middle antenna 02
    Galaxy S7 Edge - Removing the middle antenna 03
    1. Pull the middle antenna out of the enclosure. Note that it’s hooked onto the lower antenna.
  7. Removing the lower antenna

    Galaxy S7 Edge - Removing the lower antenna 01
    Galaxy S7 Edge - Removing the lower antenna 02
    1. Disconnect the lower antenna by using the tweezers to unhook it on the left side.
    2. Remove the antenna from the enclosure.
  8. Disconnecting the battery

    Galaxy S7 Edge - Disconnecting the battery 01
    Galaxy S7 Edge - Disconnecting the battery 02
    1. Using the spudger, carefully disconnect the battery contact from the motherboard. Carefully pry the contact out of the socket.
  9. Removing the front camera

    Galaxy S7 Edge - Removing the front camera 01
    Galaxy S7 Edge - Removing the front camera 02
    1. Using the spudger, carefully disconnect the front camera’s contact from the motherboard.
    2. Remove the front camera from the enclosure.
  10. Disconnecting all the contacts from the motherboard

    Galaxy S7 Edge - Disconnecting all the contacts from the motherboard 01
    Galaxy S7 Edge - Disconnecting all the contacts from the motherboard 02
    Galaxy S7 Edge - Disconnecting all the contacts from the motherboard 03
    Galaxy S7 Edge - Disconnecting all the contacts from the motherboard 04
    Galaxy S7 Edge - Disconnecting all the contacts from the motherboard 05
    Galaxy S7 Edge - Disconnecting all the contacts from the motherboard 06
    Galaxy S7 Edge - Disconnecting all the contacts from the motherboard 07
    Galaxy S7 Edge - Disconnecting all the contacts from the motherboard 08
    Galaxy S7 Edge - Disconnecting all the contacts from the motherboard 09
    • Volume Connector
    • Proximity Sensor
    • Earpiece Connector
    • Display
    • Power-Button
    • Antenna
    • Sensors
    1. Using the spudger, carefully disconnect the following contacts from the motherboard.
  11. Removing the motherboard

    Galaxy S7 Edge - Removing the motherboard 01
    Galaxy S7 Edge - Removing the motherboard 02
    Galaxy S7 Edge - Removing the motherboard 03
    Galaxy S7 Edge - Removing the motherboard 04
    Galaxy S7 Edge - Removing the motherboard 05
    1. The bottom of the motherboard (arrow) is connected to the USB port.
    2. Carefully tilt the board up by 180° so you can get at the contact. Don’t pull too hard on the board.
    3. Using the spudger, carefully disconnect the contact from the PCB.
    4. Remove the board.
    There's a small plastic pin in the opening of the SIM tray. Make sure it doesn't fall out.
  12. Removing the earpiece

    Galaxy S7 Edge - Removing the earpiece 01
    Galaxy S7 Edge - Removing the earpiece 02
    1. The earpiece is glued to the enclosure. Using the steel spatula, carefully detach the earpiece from the glue.
    2. Remove the earpiece from the enclosure.
  13. Removing the proximity sensor

    Galaxy S7 Edge - Removing the proximity sensor 01
    Galaxy S7 Edge - Removing the proximity sensor 02
    Galaxy S7 Edge - Removing the proximity sensor 03
    1. The proximity sensor is glued to the enclosure. Using the steel spatula, carefully detach the sensor from the glue. Start with the cable.
    2. Then detach the sensor.
    3. Remove the sensor from your device.
  14. Removing the vibration motor

    Galaxy S7 Edge - Removing the vibration motor 01
    Galaxy S7 Edge - Removing the vibration motor 02
    Galaxy S7 Edge - Removing the vibration motor 03
    1. The vibration motor is glued to the enclosure. Carefully detach the motor by inserting the steel spatula between the enclosure and the motor.
    2. Remove the motor.
  15. Removing the headphone jack

    Galaxy S7 Edge - Removing the headphone jack 01
    Galaxy S7 Edge - Removing the headphone jack 02
    Galaxy S7 Edge - Removing the headphone jack 03
    Galaxy S7 Edge - Removing the headphone jack 04
    • 1 × 3,3mm PH00 Phillips-Schraube
    1. Disconnect the headphone jack’s contact from the PCB. Using the spudger, carefully pry the contact out of the socket.
    2. Unscrew the screw holding the socket in place.
      1 x 3.3 mm PH00 Phillips screw
    3. Remove the headphone jack from the enclosure.
  16. Removing the antenna cables

    Galaxy S7 Edge - Removing the antenna cables 01
    Galaxy S7 Edge - Removing the antenna cables 02
    Galaxy S7 Edge - Removing the antenna cables 03
    Galaxy S7 Edge - Removing the antenna cables 04
    1. The two antenna cables are connected to the lower board and routed along a slot in the enclosure.
    2. First pull the white antenna cable out of the guide and then disconnect it from the lower board.
    3. Then pull the blue antenna cable out of the guide and disconnect it from the board.
  17. Removing the battery

    Galaxy S7 Edge - Removing the battery 01
    Galaxy S7 Edge - Removing the battery 02
    Galaxy S7 Edge - Removing the battery 03
    Galaxy S7 Edge - Removing the battery 04

    Be very careful during this step. Use a flat, blunt tool like the round end of the steel laboratory spatula to avoid damaging the battery.

    1. The battery is really glued to the enclosure, so be very careful when you’re removing it. Using your tool, carefully detach the battery from the enclosure. First insert your tool on the side between the battery and the enclosure and use it as a lever.
    2. Repeat this process on the opposite side of the battery.
    3. Then carefully insert your tool below the battery and detach the glue under it.
    4. Remove the battery from the enclosure.
  18. Preparing the new display

    Galaxy S7 Edge - Preparing the new display 01
    Galaxy S7 Edge - Preparing the new display 02
    Galaxy S7 Edge - Preparing the new display 03
    Galaxy S7 Edge - Preparing the new display 04
    Galaxy S7 Edge - Preparing the new display 05
    1. In the new display’s enclosure, all the adhesive surfaces and thermal pads (arrows) are covered with transparent protective film. Remove the protective film before you start with assembly.
      • At the top and on the left: adhesive pads for the battery, proximity sensor, earpiece and front camera
      • At the bottom: thermal pads
  19. Inserting the battery

    Galaxy S7 Edge - Inserting the battery 01
    Galaxy S7 Edge - Inserting the battery 02
    1. Put the battery in the enclosure. It fits perfectly into the compartment in the middle of the enclosure.
    2. Press the battery against the enclosure so the glue will stick better.
  20. Installing the antenna cables

    Galaxy S7 Edge - Installing the antenna cables 01
    Galaxy S7 Edge - Installing the antenna cables 02
    Galaxy S7 Edge - Installing the antenna cables 03
    Galaxy S7 Edge - Installing the antenna cables 04
    Galaxy S7 Edge - Installing the antenna cables 05
    1. First connect the blue antenna cable to the lower board and then route it carefully along the slot in the enclosure.
    2. Then connect the white antenna cable and put it in the guide above the blue antenna cable.
  21. Installing the headphone jack

    Galaxy S7 Edge - Installing the headphone jack 01
    Galaxy S7 Edge - Installing the headphone jack 02
    Galaxy S7 Edge - Installing the headphone jack 03
    Galaxy S7 Edge - Installing the headphone jack 04
    • 1 × 3,3mm PH00 Phillips-Schraube
    1. Put the jack in the recess in the lower edge of the enclosure.
    2. Use a screw to attach the jack to the enclosure.
    3. Connect the jack’s contact to the PCB. You should be able to hear it click into place.
  22. Installing the vibration motor

    Galaxy S7 Edge - Installing the vibration motor 01
    Galaxy S7 Edge - Installing the vibration motor 02
    1. Put the vibration motor in the little round recess on the left side of the enclosure. Use your fingers to press the motor firmly into place.
  23. Installing the proximity sensor

    Galaxy S7 Edge - Installing the proximity sensor 01
    Galaxy S7 Edge - Installing the proximity sensor 02
    1. Put the proximity sensor in the recess in the upper edge of the enclosure. Press on the sensor firmly with your finger so the glue will stick.
  24. Installing the earpiece

    Galaxy S7 Edge - Installing the earpiece 01
    Galaxy S7 Edge - Installing the earpiece 02
    1. Put the earpiece in the little recess in the upper edge of the enclosure.
    2. Press the earpiece on a little so the glue will stick.
  25. Installing the motherboard

    Galaxy S7 Edge - Installing the motherboard 01
    Galaxy S7 Edge - Installing the motherboard 02
    Galaxy S7 Edge - Installing the motherboard 03
    1. Turn the board upside down and put it at the lower end of the enclosure to reconnect the USB port’s contact.
    2. Connect the contact so you can hear it click into the socket.
    3. Fold the board over so you can put it in the enclosure.
  26. Connecting all the contacts from the motherboard

    Galaxy S7 Edge - Connecting all the contacts from the motherboard 01
    Galaxy S7 Edge - Connecting all the contacts from the motherboard 02
    Galaxy S7 Edge - Connecting all the contacts from the motherboard 03
    Galaxy S7 Edge - Connecting all the contacts from the motherboard 04
    Galaxy S7 Edge - Connecting all the contacts from the motherboard 05
    Galaxy S7 Edge - Connecting all the contacts from the motherboard 06
    Galaxy S7 Edge - Connecting all the contacts from the motherboard 07
    Galaxy S7 Edge - Connecting all the contacts from the motherboard 08
    Galaxy S7 Edge - Connecting all the contacts from the motherboard 09
    • Proximity Sensor
    • Earpiece Connector
    • Display
    • Power-Button
    • Antenna
    • Sensors
    • Volume Connector
    1. Connect the contacts to the motherboard.
  27. Installing the front camera

    Galaxy S7 Edge - Installing the front camera 01
    Galaxy S7 Edge - Installing the front camera 02
    Galaxy S7 Edge - Installing the front camera 03
    1. Put the front camera in the recess in the upper edge of the enclosure.
    2. Connect the camera to the motherboard. You have to hear the contact click into place.
  28. Connecting the battery

    Galaxy S7 Edge - Connecting the battery 01
    Galaxy S7 Edge - Connecting the battery 02
    1. Connect the battery to the motherboard. Press the contact into the socket on the motherboard until you hear it click into place.
  29. Installing the lower antenna

    Galaxy S7 Edge - Installing the lower antenna 01
    Galaxy S7 Edge - Installing the lower antenna 02
    1. Put the antenna at the lower end of the enclosure.
    2. Press on the antenna with your fingers until it clicks into place in the enclosure.
  30. Installing the middle antenna

    Galaxy S7 Edge - Installing the middle antenna 01
    Galaxy S7 Edge - Installing the middle antenna 02
    1. Put the antenna back in the enclosure after hooking it onto the lower antenna.
    2. Press on the antenna with your fingers until it clicks into place in the enclosure.
  31. Installing the upper antenna

    Galaxy S7 Edge - Installing the upper antenna 01
    Galaxy S7 Edge - Installing the upper antenna 02
    Galaxy S7 Edge - Installing the upper antenna 03
    1. Put the antenna back in the enclosure. First put it on the left side and then press it on firmly with your fingers.
    2. You should be able to hear the antenna click into place.
  32. Fastening the screws

    Galaxy S7 Edge - Fastening the screws 01
    Galaxy S7 Edge - Fastening the screws 02
    Galaxy S7 Edge - Fastening the screws 03
    Galaxy S7 Edge - Fastening the screws 04
    • 12 × 3,3mm PH00 Phillips-Schrauben
    1. Put the yellow adhesive strip back on.
    2. Attach the three antennas using the twelve screws.
      12 x 3.3 mm PH00 Phillips screws
  33. Attaching the back cover

    Galaxy S7 Edge - Attaching the back cover 01
    Galaxy S7 Edge - Attaching the back cover 02
    Galaxy S7 Edge - Attaching the back cover 03
    1. Put the back cover back in its original position.
    2. Press the back cover on all over so the glue will stick.
    3. You can also heat your device with hot air and then clamp it or weight it down with a couple books so the glue will stick better.
  34. Inserting the SIM and microSD cards

    Galaxy S7 Edge - Inserting the SIM and microSD cards 01
    1. Insert the SIM tray back into your device. Make sure the tray is positioned properly.
  35. Testing the display

    Galaxy S7 Edge - Testing the display 01
    Galaxy S7 Edge - Testing the display 02
    1. Turn on your device and then drag any app across the entire screen. Drag the app once around the entire border and then in a zigzag across the screen. The app should always follow your finger. Then test the display brightness again by dragging the brightness slider to minimum and maximum.
  36. Optional: checking functions in test mode

Ø 4.4 (45 Bewertungen)

Bewerte unsere Anleitung

Hat dir unsere Anleitung weitergeholfen? Wir sind auf deine Beurteilung gespannt.

Bewertung abgeben

Bewertung abgeben

Wie findest du unsere Reparatur-Anleitung Galaxy S7 Edge Replacing the display?

Exzellent

Similar guides

You might also be interested in these guides.

You might be interested in

Get in touch with iDoc

Please contact our customer service for any questions about iDoc's products and services.

  • Send a message

    If you have a question about a guide or want to give us general feedback, just use our contact form

    Write a message
  • Free shipping

    From a minimum order value of 39.00 € your order will be shipped free of charge within Germany.

  • Call iDoc

    If you have any questions about our guides or services, call us from Monday to Friday, 10:00 a.m. to 6:00 p.m.

    +49 30 200 514 455
  • 5 star service

    We offer top quality and service. Our customers confirm this as well.

    Show reviews