Samsung Galaxy S10e - Screen replacement

Replace the defective display unit of your Galaxy S10e by yourself

  • Galaxy S10e
  • 23 Steps
  • Difficult
  • 90 min.
Go to the guide

Introduction

With this detailed step-by-step guide, you can easily replace your Galaxy S10e display at home.

A replacement is necessary when the glass is shattered, the touchscreen does not respond to touch anymore, or the display remains black or flickers. During this repair, we replace the entire display unit including the frame, not just the broken screen. You may have to take some small parts from the old display unit, depending on how the new spare part is equipped.

The repair is a bit difficult as the Galaxy S10e has to be opened via the glass backcover. Removing the back cover is a somewhat more diffucult procedure, so plan enough time for it.

Do a backup before the repair, use a clean work surface and reserve enough time. If you are stuck at any point, just contact our live chat or write a comment on the corresponding step.

Required tools

  • Flache Plektren

    Flache Plektren

    You need a very flat tool such as a flat pick to pry out parts that are glued in place.

    €1.00 at the iDoc store
  • Heat gun

    Heat gun

    You can use a heat gun to heat parts that are glued on so they’re easier to remove. In most cases, you can also use a hairdryer.

    from €14.99 on Amazon
  • For storing screws

    For storing screws

    We recommend storing your screws so you don’t mix up the various screws and small parts.

    €10.00 at the iDoc store
  • iFlex opening tool

    iFlex opening tool

    Die kleinen Teile in deinem Smartphone auseinanderzukriegen kann eine sehr große Arbeit bedeuten. Die Klinge des kompakten aber stabilen iFlex hat eine Dicke von nur 0,15 mm, sodass es auch in den kleinsten Spalten reinpasst, beispielsweise zwischen dem Display und dem Rahmen oder unter dem Logicboard. Das praktische iFlex ist aus hochwertigem rostfreiem Stahl und liegt gut in der Hand. Damit ist es der perfekte Helfer bei jeder Smartphone-Reparatur.

    €9.00 at the iDoc store
  • iPlastix

    iPlastix

    Dein Smartphone zu öffnen kann eine sehr empfindliche Angelegenheit sein. Die Klinge des biegsamen aber stabilen iPlastix hat eine Dicke von nur 0,15 mm, sodass es auch in den kleinsten Spalten reinpasst, beispielsweise zwischen dem Display und dem Rahmen oder unter dem Logicboard. Das praktische iPlastix ist aus biegsamem Kunststoff und liegt gut in der Hand. Damit ist es der perfekte Helfer bei jeder Smartphone-Reparatur.

    €9.00 at the iDoc store
  • Tweezers

    Tweezers

    We recommend using tweezers to remove screws and various small parts from your device.

    €16.00 at the iDoc store
  • Sim Tool

    Sim Tool

    Wenn du eine andere SIM-Karte benutzen willst, musst du die alte zunächst entfernen. Auch bei den meisten Reparaturen an deinem Apple-Gerät muss die SIM-Karte zuerst entfernt werden. Der SIM-Karten-Schlitten kommt allerdings nur dann heraus, wenn du ein Werkzeug mit einer sehr dünnen Spitze in das kleine Loch neben dem SIM-Karten-Schacht einführst. Dieses Werkzeug ist speziell für das Auswerfen der SIM-Karte bei allen iPhones und iPads gefertigt und passt perfekt in die entsprechende Öffnung hinein.

    €1.00 at the iDoc store
  • Plastic prying tool

    Plastic prying tool

    You need a flat plastic prying tool to disconnect the various plugs and connectors.

    €1.00 at the iDoc store
  • Steel Laboratory Spatula

    Steel Laboratory Spatula

    You need a flat and sturdy prying tool to disconnect glued parts.

    €9.00 at the iDoc store
  • Suction cup

    Suction cup

    A suction cup is perfect for lifting smooth surfaces such as displays or rear glass panels.

    €2.00 at the iDoc store
  • Phillips PH00 screwdriver

    Phillips PH00 screwdriver

    You need the right screwdriver for removing PH00 screws.

    €10.00 at the iDoc store

Required replacement part

  • Samsung Galaxy S10e Display Schwarz / Prism Black

    Samsung Galaxy S10e Display Schwarz / Prism Black

    Das Infinity-O Display verspricht grenzenlosen Spaß mit deinem Samsung Galaxy S10e. Grenzenlos? Nicht ganz, denn leider ist auch dieses Smartphone nicht vor einem Sturzschaden oder einem Defekt gewappnet. Solltest auch du die Grenzen deines Samsung Galaxy S10e überreizt haben, bieten wir dir ein nagelneues Display an. Das Ersatzteil ist original von Samsung, du kannst die gewohnte Qualität also auch weiterhin genießen. Selbst der Fingerabdrucksensor im Rahmen wird wieder wie früher funktionieren! Viel Freude mit deinem reparierten Samsung Galaxy S10e!

    €179.00 at the iDoc store
  • Samsung Galaxy S10e Klebeset für Back Cover

    Samsung Galaxy S10e Klebeset für Back Cover

    Wenn du dein Samsung Galaxy S10e öffnest, um beispielsweise das Display oder den Akku zu tauschen, musst du unweigerlich das Back Cover abnehmen. Dieses ist verklebt - beim Öffnen des Smartphones kann es passieren, dass die ursprünglichen Klebeflächen teilweise abgehen oder ihre Klebekraft verlieren. Auch wenn es nicht zwingend erforderlich ist: Willst du beim Wiederverschließen deines Samsung Galaxy S10e auf Nummer sicher gehen, kannst du dir ein original Klebeset inklusive aller Klebeflächen sowie zusätzliche Schrauben für das Mainboard besorgen. Damit bist du bei den Reparaturen an deinem Samsung Galaxy S10e bestens gewappnet.

    €6.00 at the iDoc store
Show all replacement parts for the Galaxy S10e 

Replacement parts and tools for this repair

Our tools plus the right spare part help you fix your device easily.

Samsung Galaxy S10e Display Blau / Prism Blue

Das Infinity-O Display verspricht grenzenlosen Spaß mit deinem Samsung Galaxy S10e. Grenzenlos? Nicht ganz, denn leider ist...

Werkzeugset Samsung

Ganz gleich, welches Problem dein Handy hat - mit unserem Werkzeugset kannst du es bestimmt beheben. Dieses Reparaturset umfasst jeweils einen...

together for €228.00

Samsung Galaxy S10e Display Gelb / Canary Yellow

Das Infinity-O Display verspricht grenzenlosen Spaß mit deinem Samsung Galaxy S10e. Grenzenlos? Nicht ganz, denn leider ist...

Werkzeugset Samsung

Ganz gleich, welches Problem dein Handy hat - mit unserem Werkzeugset kannst du es bestimmt beheben. Dieses Reparaturset umfasst jeweils einen...

together for €228.00

Samsung Galaxy S10e Display Grün / Prism Green

Das Infinity-O Display verspricht grenzenlosen Spaß mit deinem Samsung Galaxy S10e. Grenzenlos? Nicht ganz, denn leider ist...

Werkzeugset Samsung

Ganz gleich, welches Problem dein Handy hat - mit unserem Werkzeugset kannst du es bestimmt beheben. Dieses Reparaturset umfasst jeweils einen...

together for €228.00

Samsung Galaxy S10e Display Schwarz / Prism Black

Das Infinity-O Display verspricht grenzenlosen Spaß mit deinem Samsung Galaxy S10e. Grenzenlos? Nicht ganz, denn leider ist...

Werkzeugset Samsung

Ganz gleich, welches Problem dein Handy hat - mit unserem Werkzeugset kannst du es bestimmt beheben. Dieses Reparaturset umfasst jeweils einen...

together for €228.00

Samsung Galaxy S10e Display Weiß / Prism White

Das Infinity-O Display verspricht grenzenlosen Spaß mit deinem Samsung Galaxy S10e. Grenzenlos? Nicht ganz, denn leider ist...

Werkzeugset Samsung

Ganz gleich, welches Problem dein Handy hat - mit unserem Werkzeugset kannst du es bestimmt beheben. Dieses Reparaturset umfasst jeweils einen...

together for €228.00

Getting started

If you get stuck or have questions, you can post a comment for each step. We’d be happy to help.

23 steps
  1. Switching off your device

    Galaxy S10e - Switching off your device 01
    Galaxy S10e - Switching off your device 02
    1. Turn off your device by holding down the power button until the “Power off” option appears.
    2. Use your finger to confirm that you want to shut down your device and wait until the screen goes blank.

    Klick the small Play button in the top right of an image to play a video for each step.

  2. Removing the back cover

    Galaxy S10e - Removing the back cover 01
    Galaxy S10e - Removing the back cover 02
    Galaxy S10e - Removing the back cover 03
    Galaxy S10e - Removing the back cover 04
    Galaxy S10e - Removing the back cover 05
    Galaxy S10e - Removing the back cover 06
    Galaxy S10e - Removing the back cover 07
    Galaxy S10e - Removing the back cover 08
    1. The back cover’s heavily glued to the chassis. Heat the device evenly with hot air to soften the glue. A temperature of 60 - 80°C should be sufficient. As a rule of thumb, you should still be able to touch your device without it being uncomfortably hot.
    2. The easiest way to loosen the back cover is to use a flat and flexible tool such as the iPlastix or iFlex. You will also need several picks to unstick the back cover all around.
    3. Heat the spot where you start and place a flat tool between the back cover and the frame.

    The iPlastix is made of plastic, so it won't scratch the device. On the other hand, it's very soft and tricky to insert. The iFlex makes it easier to get into the gap between the glass and the frame because it's made of very thin, stable metal. But it also makes it easier to scratch the frame of your S10e. To get into the gap initially, you can use the iFlex and then continue with the iPlastix as soon as possible.

    Be extra careful, the back cover can break very easily. If necessary, apply the heat several times and try again. Removing the back cover might take half an hour. Take a little more time and work carefully to make sure you don't break anything.

    1. Once the tool is inserted, stick a pick into the gap to keep it open. Then run the tool around the entire edge to gradually loosen the glue.
    2. Then heat the next part and insert the picks one by one.
    Use a suction cup to lift the glass if you can’t find anywhere to insert the tool.
  3. Removing the plastic cover

    Galaxy S10e - Removing the plastic cover 01
    Galaxy S10e - Removing the plastic cover 02
    Galaxy S10e - Removing the plastic cover 03
    • 8 × 3,9 mm Phillips
    1. Loosen the Phillips screws that secure the cover. The contactless charging coil and NFC antenna are attached to the plastic cover.
    2. The cover is hooked into the top of the housing and the lower part is lightly glued on. Carefully slide a flat tool under the attached areas and loosen them.
    3. Now you can remove the cover together with the coil.
  4. Disconnecting the battery

    Galaxy S10e - Disconnecting the battery 01
    Galaxy S10e - Disconnecting the battery 02
    • Battery Connector
    1. Using the spudger, carefully disconnect the battery contact from the motherboard.

    Always lever from a side where there are no small components on the motherboard. This avoids unintentional damage to capacitors or ICs.

  5. Removing the battery

    Galaxy S10e - Removing the battery 01
    Galaxy S10e - Removing the battery 02
    Galaxy S10e - Removing the battery 03
    Galaxy S10e - Removing the battery 04
    Galaxy S10e - Removing the battery 05
    Galaxy S10e - Removing the battery 06

    The battery is strongly glued, so you should use hot air again to loosen the glue. The glue is on the edge of the battery but not in the middle.

    Never heat the battery directly and avoid bending it.

    1. Heat the battery from below via the display.
    2. We recommend using a flat tool like the iPlastix or an iSesamo to go around the battery and lever it carefully.
    3. When the glue is loosened everywhere, lift the battery and remove it from the device.

    If you only replace the battery, be careful not to insert the tool too far to avoid damaging the back of the display.Be careful not to damage the battery. Take your time again and heat the glue several times.


  6. Removing the front-facing camera

    Galaxy S10e - Removing the front-facing camera  01
    Galaxy S10e - Removing the front-facing camera  02
    Galaxy S10e - Removing the front-facing camera  03
    • Camera Connector
    1. Now disconnect the front camera connector using a spudger.
    2. Pry it up from the free side where there are no PCB components.
    3. Then take the camera out of its holder.
  7. Removing the speaker

    Galaxy S10e - Removing the speaker  01
    Galaxy S10e - Removing the speaker  02
    Galaxy S10e - Removing the speaker  03
    • 7 × 3,9 mm Phillips
    1. Loosen the Phillips screws that secure the speaker and then remove it.
    2. You can loosen the speaker more easily by lifting it up a little at the openings at the side. The openings are marked with small triangular arrows.
  8. Removing the headphone jack

    Galaxy S10e -  Removing the headphone jack 01
    Galaxy S10e -  Removing the headphone jack 02
    Galaxy S10e -  Removing the headphone jack 03
    Galaxy S10e -  Removing the headphone jack 04
    • Connector
    1. Disconnect the headphone jack connector from the motherboard. Carefully position the spudger and remove the connector.
    2. Lever the side of the jack to release it and then remove it from the case.



  9. Removing the mainboard

    Galaxy S10e - Removing the mainboard 01
    Galaxy S10e - Removing the mainboard 02
    Galaxy S10e - Removing the mainboard 03
    Galaxy S10e - Removing the mainboard 04
    Galaxy S10e - Removing the mainboard 05
    • 3 × 3,7 mm Phillips
    • Connector
    1. Using the spudger, carefully disconnect the marked contacts from the motherboard.
    2. Remove the several Phillips screws.
    3. Take the SIM card holder out.
    4. Now you can carefully remove the motherboard. Make sure it doesn’t get caught on the connectors you already disconnected.
    5. Then set the board aside in a safe place.
    There's a small plastic pin in the opening of the SIM tray. Make sure it doesn't fall out.
  10. Removing the earpiece

    Galaxy S10e - Removing the earpiece 01
    Galaxy S10e - Removing the earpiece 02
    Galaxy S10e - Removing the earpiece 03
    Galaxy S10e - Removing the earpiece 04

    If your replacement display already has a earpiece installed, you can skip this step.

    The earpiece is glued to the enclosure. Carefully detach it with a flat tool like the steel spatula.

  11. Removing the vibration motor

    Galaxy S10e - Removing the vibration motor 01
    Galaxy S10e - Removing the vibration motor 02

    If your replacement display already has a vibration motor installed, you can skip this step.

    1. The vibration motor is glued to the enclosure. Carefully detach the motor by inserting your tool between the enclosure and the motor.

    Do not lever on the side with the golden contacts, as these can easily break off.

  12. Preparing the new display

    Galaxy S10e - Preparing the new display 01
    Galaxy S10e - Preparing the new display 02
    Galaxy S10e - Preparing the new display 03
    1. Now take the new display and compare it to the old one. If necessary, you have to reuse some gaskets or holders.
    2. Remove the backing films from the sticker surfaces, so you can attach the front camera or the battery, for example.
  13. Inserting the vibration motor

    Galaxy S10e - Inserting the vibration motor 01
    Galaxy S10e - Inserting the vibration motor 02
    1. Put the vibration motor in the little round opening on side of the case.
    2. Use your fingers to press the motor firmly into place.
  14. Inserting the earpiece

    Galaxy S10e - Inserting the earpiece 01
    Galaxy S10e - Inserting the earpiece 02
    1. Put the earpiece back in the case.
    2. Press it on a little so the glue will stick better.
  15. Inserting the mainboard

    Galaxy S10e - Inserting the mainboard 01
    Galaxy S10e - Inserting the mainboard 02
    Galaxy S10e - Inserting the mainboard 03
    Galaxy S10e - Inserting the mainboard 04
    Galaxy S10e - Inserting the mainboard 05
    Galaxy S10e - Inserting the mainboard 06
    • 3 × 3,7 mm Phillips
    • Connector
    1. Take the motherboard and carefully place it into the device. Be careful not to pinch any cables. Bend all connectors to the side.
    2. First place the board at the bottom and press the charging socket into its opening. Then press the board down until it is correctly positioned everywhere.
    3. Insert the SIM card holder. If it's stuck, don't push it in with force. In this case check if the mainboard is correctly seated.
    4. Then fasten the screws of the motherboard.
    5. Finally reconnect all connectors.
  16. Installing the headphone jack

    Galaxy S10e - Installing the headphone jack 01
    Galaxy S10e - Installing the headphone jack 02
    Galaxy S10e - Installing the headphone jack 03
    • Connector
    1. Insert the audio jack and press it lightly until it clicks into place.
    2. Then connect the connector again.



  17. Installing the speaker

    Galaxy S10e - Installing the speaker 01
    Galaxy S10e - Installing the speaker 02
    • 7 × 3,9 mm Phillips
    1. Then place the speaker back over the USB port, press it in and screw it tight.
    2. Make sure it's latched in at the bottom.
  18. Installing the front-facing camera

    Galaxy S10e - Installing the front-facing camera 01
    Galaxy S10e - Installing the front-facing camera 02
    Galaxy S10e - Installing the front-facing camera 03
    Galaxy S10e - Installing the front-facing camera 04
    • Camera Connector

    Insert the front camera and attach its connector.

    Make sure that all protective films are removed and that the lens of the camera is dust free.

  19. Inserting the battery

    Galaxy S10e - Inserting the battery 01
    Galaxy S10e - Inserting the battery 02
    1. Put the battery in the display unit.
    2. Press the battery firmly into the frame so the glue will stick better.

    Remove excess adhesive so that the battery sits flat in the phone.

  20. Connecting the battery

    Galaxy S10e - Connecting the battery 01
    Galaxy S10e - Connecting the battery 02
    • Battery Connector
    1. Connect the battery to the motherboard. Press the contact onto the connection on the motherboard until you hear it click into place.
  21. Installing the plastic cover

    Galaxy S10e - Installing the plastic cover 01
    Galaxy S10e - Installing the plastic cover 02
    Galaxy S10e - Installing the plastic cover 03
    • 8 × 3,9 mm Phillips
    1. Put the cover with the antenna back in the enclosure after hooking it onto the top of the enclosure.
    2. Then press the cover with your fingers until it clicks gently into place.
    3. Fasten the phillips screws.
  22. Testing the device

    Galaxy S10e - Testing the device 01
    Galaxy S10e - Testing the device 02
    Galaxy S10e - Testing the device 03
    1. Turn on your device and test it with the integrated test mode.
    2. Access the test mode by dialing *#0*#
    3. Follow the instructions and test the screen, the cameras and the sensors

    Test especially all functions of the part you replaced.

  23. Attaching the back cover

    Galaxy S10e - Attaching the back cover 01
    Galaxy S10e - Attaching the back cover 02
    Galaxy S10e - Attaching the back cover 03

    If the adhesive on the back cover is still intact, you can seal your device without using a new adhesive frame.

    1. Put the back cover back in its original position.
    2. Press the back cover on all over so the glue will stick.

    You can also heat your device with hot air and then clamp it or weight it down with a couple books so the glue will stick better.

    If you install a new backcover, now remove the last protective films from the adhesive surfaces.
Ø 0 (0 Bewertungen)

Bewerte unsere Anleitung

Hat dir unsere Anleitung weitergeholfen? Wir sind auf deine Beurteilung gespannt.

Bewertung abgeben

Bewertung abgeben

Wie findest du unsere Reparatur-Anleitung Galaxy S10e Screen replacement?

Exzellent

Similar guides

You might also be interested in these guides.

You might be interested in

Get in touch with iDoc

Please contact our customer service for any questions about iDoc's products and services.

  • Send a message

    If you have a question about a guide or want to give us general feedback, just use our contact form

    Write a message
  • Free shipping

    From a minimum order value of 39.00 € your order will be shipped free of charge within Germany.

  • Call iDoc

    If you have any questions about our guides or services, call us from Monday to Friday, 10:00 a.m. to 6:00 p.m.

    +49 30 200 514 455
  • 5 star service

    We offer top quality and service. Our customers confirm this as well.

    Show reviews