OnePlus 2 battery repair guide

The battery life is low. Your OnePlus 2 keeps crashing or won’t charge.

In this repair guide, we show you how to replace your OnePlus 2 defective battery on your own. This repair can help if your OnePlus 2 crashes during heavy use because the voltage temporarily drops, you can no longer charge it or turn it on, or the battery life is very low.

Required tools

Flat Picks

Flat Picks

You need a very flat tool such as a flat pick to pry out parts that are glued in place.
€2.00 at the iDoc store
Heat gun

Heat gun

You can use a heat gun to heat parts that are glued on so they’re easier to remove. In most cases, you can also use a hairdryer.
from €14.47 on Amazon
For storing screws

For storing screws

We recommend storing your screws so you don’t mix up the various screws and small parts.
€10.00 at the iDoc store
Menda ESD Spudger

Menda ESD Spudger

You need a flat plastic prying tool to disconnect the various plugs and connectors.
€7.00 at the iDoc store
Tweezers

Tweezers

We recommend using tweezers to remove screws and various small parts from your device.
€11.00 at the iDoc store
Pick Set

Pick Set

You need a flat but stable tool such as a pick to pry out parts that are glued in place.
€2.00 at the iDoc store
Plastic prying tool

Plastic prying tool

You need a flat plastic prying tool to disconnect the various plugs and connectors.
€2.00 at the iDoc store
Steel Laboratory Spatula

Steel Laboratory Spatula

You need a flat and sturdy prying tool to disconnect glued parts.
€5.00 at the iDoc store
Phillips PH00 screwdriver

Phillips PH00 screwdriver

You need the right screwdriver for removing PH00 screws.
€10.00 at the iDoc store

Show all replacement parts for the OnePlus 2

Passendes Werkzeug

Mit unserem Werkzeug gelingt dir die Reparatur.

Samsung Tool Kit, 17 pieces

for €45.00

Steps

9 Steps

Switch off device

Step 1

Removing the back cover

Step 2

Removing the SIM card tray

Step 3

Removing the plastic cover

Step 4

Removing the battery

Step 5

Installing the battery

Step 6

Attaching the plastic cover

Step 7

Inserting the Sim tray

Step 8

Attaching the back cover

Step 9

Getting started with the repair of your OnePlus 2

If you get stuck or have questions, you can post a comment. We’d be happy to help.

9 steps

Switch off device
Turn off your device by holding down the power button until the “Power off” option appears.
Use your finger to confirm that you want to shut down your OnePlus 2 and wait until the screen goes blank.
Removing the back cover
Insert a thin, flat, tapered spudger into the gap at the corner of your smartphone. There are several clips on the outside under the back cover. You have to disconnect them by moving the spudger around the entire smartphone one time. Alternatively, you can detach the back cover using your fingernails.
Then you can take off the back cover.
Removing the SIM card tray
You can use the SIM Tool or a paperclip to remove the SIM card tray. Press the SIM Tool into the small hole in the SIM card tray to remove it.
Removing the plastic cover
6 × Gummiabdeckung

18 × Phillips-Schraube

Remove all 18 Phillips screws that hold the plastic cover in place.
6 Phillips screws are hidden under a rubber cover. Use a sharp object to lift out the cover.
Lift out the logic board cover. Carefully insert the pointed tip of the ESD spudger and lift the black cover. Also pry it out at other points.

Removing the battery
If your OnePlus 2 is still on, turn it off now by holding down the standby button for about three seconds and following the prompt on the display.

Now you can detach the battery connector. Be very careful. Place the pointed tip of the spudger very slightly below the contact and carefully lift it up. The pictures show where you should put the spudger to avoid breaking off the little resistors even if it slips.
The battery is slightly glued to the cover. You can warm it, ot remove it more easily.

Now lift the battery with the spudger and then remove it.
Installing the battery
Put the battery back in and connect it.
Attaching the plastic cover
18 × Phillips-Schraube

6 × Gummistöpsel

Now put the cover back on.
Then fasten all the Phillips screws again.
Don’t forget to put the little rubber plugs back in.
Inserting the Sim tray
Insert the sim tray
Attaching the back cover
It’s very easy to put the back cover back on. Put it on in the correct position and press it on all the way around the phone until it’s completely clicked into place.