You can barely hear anything when you're having a call on your iPhone 13?

Replace your earpiece to fix this problem! In this detailed photo tutorial, we will show you step by step how to do it best.

Once you open your iPhone its specified IP68 certification will expire.

To prevent the case from scratches, make sure your workspace is clean and level.

We wish you good luck with your repair!

Required tools

  • Flat Picks

    Flat Picks

    You need a very flat tool such as a flat pick to pry out parts that are glued in place.

    €5.00 at the iDoc store
  • Heat gun

    Heat gun

    You can use a heat gun to heat parts that are glued on so they’re easier to remove. In most cases, you can also use a hairdryer.

    from €14.47 on Amazon
  • Menda ESD Spudger

    Menda ESD Spudger

    You need a flat plastic prying tool to disconnect the various plugs and connectors.

    €7.00 at the iDoc store
  • Plastic prying tool

    Plastic prying tool

    You need a flat plastic prying tool to disconnect the various plugs and connectors.

    €2.00 at the iDoc store
  • Pentalobe PL1 screwdriver

    Pentalobe PL1 screwdriver

    You need the right screwdriver for removing pentalobe PL1 screws.

    €12.00 at the iDoc store
  • Phillips PH00 screwdriver

    Phillips PH00 screwdriver

    You need the right screwdriver for removing PH00 screws.

    €12.00 at the iDoc store
  • Phillips screwdriver with centering pin

    Phillips screwdriver with centering pin

    Phillips screwdriver with practical centering pin for logic board screws.

    €12.00 at the iDoc store
  • Y-type Y000 screwdriver

    Y-type Y000 screwdriver

    You need the right screwdriver for removing Y-type screws.

    €12.00 at the iDoc store

Required replacement part

Show all replacement parts for the iPhone 13 

Replacement parts and tools for this repair

Our tools plus the right spare part help you fix your device easily.

Getting started with the repair of your iPhone 13

If you get stuck or have questions, you can post a comment. We’d be happy to help.

21 steps
  1. Switching off your iPhone12

    iPhone 13 - Switching off your iPhone12 01
    iPhone 13 - Switching off your iPhone12 02
    iPhone 13 - Switching off your iPhone12 03

    Before repairing, we recommend that you use our checklist to test the basic functions of your iPhone 13. This way you can check afterwards if your repair was successful.

    1. Press and hold the side and volume down key simultaneously for a few seconds.
    2. Wipe the displayed slider from left to right.
  2. Unscrewing the screen

    • 2 × 6.8 mm Pentalobe

    Once you open your iPhone its specified IP68 certification will expire.

    We recommend using a screw storage to keep all disassembled parts and screws safe and organized. Our magnetic pad has the additional advantage that nothing can move on it.

    1. Unscrew the two Pentalobe screws left and right of the Lightning connector.
    2. Then put them into a screw storage.
  3. Heating up the edge of the screen

    iPhone 13 - Heating up the edge of the screen 01
    iPhone 13 - Heating up the edge of the screen 02
    Used tools
    Heat gun

    The screen of the iPhone 13 is heavily glued. In order to remove it, you first have to heat the adhesive sufficiently with hot air. For this, use a hot air device, such as a hot air dryer or an ordinary hair dryer.

    1. Run a hot air device evenly over the edge of the screen.
    Used tools
  4. Lifting up the screen

    We recommend a flat pick to insert between the screen and the case unit. Alternatively, the iPlastix and iFlex can be helpful as well.

    1. Attach a suction cup to the lower edge of the screen and pull it firmly upwards to create a narrow gap between the screen and the case unit.
    2. Insert a flat, stable tool into the gap to enlarge it.
  5. Detaching the screen

    Do not insert your tool too far on the side of the volume buttons to avoid damaging any cables inside the device.
    Be careful not to open the screen too far while the sensitive screen cables are still attached.

    1. Move the plastic tool once around the edge of the screen. Press it upwards at the same time to release its hooked lugs from the case unit.
    2. When the screen is completely detached, you can carefully unfold it towards the volume buttons. Lean it against a stable object.
    Used tools
  6. Removing the cover plates

    • 4 × 1.2 mm Phillips
    • 1 × 1.7 mm Y-Type
    • 1 × 1.6 mm Phillips

    To remove the screen completely, you have to detach the battery connector as well as the two screen connectors. These are located under two cover plates.

    The upper cover plate is hooked on one side.

    1. Unscrew the six screws from the two cover plates and put them in your screw storage.
    2. Then carefully remove the plates from your device with a pair of tweezers.
  7. Disconnecting the battery

    iPhone 13 - Disconnecting the battery 01
    iPhone 13 - Disconnecting the battery 02
    iPhone 13 - Disconnecting the battery 03
    Used tools
    • Connector
    To avoid a potential short circuit during the repair, you should always detach the battery connector first.
    1. Use a plastic lever tool to move under the connector and carefully separate it from the board. We use a plastic spudger for this.
    Used tools
  8. Disconnecting the screen

    iPhone 13 - Disconnecting the screen 01
    iPhone 13 - Disconnecting the screen 02
    iPhone 13 - Disconnecting the screen 03
    iPhone 13 - Disconnecting the screen 04
    iPhone 13 - Disconnecting the screen 05
    Used tools
    • Connector
    1. Pry the two screen connectors carefully off the logic board with a spudger.
    2. Then put the fully detached screen aside.
    Used tools
  9. Detaching the connectors on the logic board

    iPhone 13 - Detaching the connectors on the logic board 01
    iPhone 13 - Detaching the connectors on the logic board 02
    iPhone 13 - Detaching the connectors on the logic board 03
    iPhone 13 - Detaching the connectors on the logic board 04
    iPhone 13 - Detaching the connectors on the logic board 05
    Used tools
    • Connector

    Before you can remove the logic board, you first have to detach all twelve connectors on it. Note that in some cases two connectors are located underneath each other.

    1. Carefully separate the connectors from the board with a spudger.
    Used tools
  10. Unscrewing the logic board

    • 1 × 3.3 mm Standoff
    • 1 × 1.6 mm Phillips
    • 1 × 3.9 mm Standoff

    Be careful not to damage any connectors when removing the logic board. It is best to hold them aside with tweezers for this purpose.

    1. Loosen the three screws that hold the board in the case.
    2. Then carefully take the logic board out of the device.
  11. The right tools for your repair

    With the right tools, you will succeed in any repair. In our store you will find a large selection of professional quality tools.
    VIEW NOW
  12. Unscrewing the earpiece

    • 1 × 1.4 mm Phillips
    • 1 × 3.6 mm Standoff
    1. Remove the two screws of the earpiece.
    2. Then take the detached earpiece out of the device.
  13. Inserting the new earpiece

    • 1 × 1.4 mm Phillips
    • 1 × 3.6 mm Standoff

    Be careful not to mix up the screw lengths. A too long screw in the wrong place may damage the device.

    1. Insert the new earpiece and screw it in place.
    Verwendete Ersatzteile
  14. Inserting the logic board

    • 1 × 3.3 mm Standoff
    • 1 × 3.9 mm Standoff
    • 1 × 1.6 mm Phillips

    Make sure not to pinch any connectors when inserting the logic board. It is best to hold them aside with a pair of tweezers.

    1. Put the logic board back into the case. Make sure that it sits level.
    2. Then fix it again with the three screws.
  15. Attaching connectors on the logic board

    iPhone 13 - Attaching connectors on the logic board 01
    iPhone 13 - Attaching connectors on the logic board 02
    iPhone 13 - Attaching connectors on the logic board 03
    iPhone 13 - Attaching connectors on the logic board 04
    • Connector

    Never press down connectors with force. Damage can lead to the failure of an entire component.Do not connect the battery yet.

    1. Reattach all twelve connectors to the logic board by carefully pressing them down. You should hear and feel them click into place.
  16. Installing a new adhesive frame (optional)

    iPhone 13 - Installing a new adhesive frame (optional) 01
    iPhone 13 - Installing a new adhesive frame (optional) 02
    iPhone 13 - Installing a new adhesive frame (optional) 03
    iPhone 13 - Installing a new adhesive frame (optional) 04
    iPhone 13 - Installing a new adhesive frame (optional) 05
    Used tools
    Heat gun
    Verwendete Ersatzteile

    If the adhesive frame is still in good condition, you do not need to install a new one. However, if it is defective or no longer sticks properly, we recommend replacing it with a new one.

    1. Heat up the adhesive frame and pull it off bit by bit with a pair of tweezers.
    2. Remove the carrier film of the adhesive frame and press it onto the edge of the case.
    3. Then remove the protective film from the upper side of the adhesive frame. The remaining protective film on the edge of the case should only be removed shortly before the end of the repair.
    Verwendete Ersatzteile
  17. Connecting the screen

    iPhone 13 - Connecting the screen 01
    iPhone 13 - Connecting the screen 02
    iPhone 13 - Connecting the screen 03
    iPhone 13 - Connecting the screen 04
    • Connector

    1. Lean the screen back against a stable object to connect it.
    2. Carefully press the two screen connectors onto the logic board one after the other. You should hear and feel them click into place.
  18. Connecting the battery

    iPhone 13 - Connecting the battery 01
    iPhone 13 - Connecting the battery 02
    iPhone 13 - Connecting the battery 03
    • Connector

    Always connect the battery last to avoid a potential short circuit.

    1. Carefully press the connector onto the logicboard, so that you can hear and feel it click into place.
  19. Testing the new earpiece

    iPhone 13 - Testing the new earpiece 01
    iPhone 13 - Testing the new earpiece 02
    iPhone 13 - Testing the new earpiece 03

    Before you close your iPhone 13 for good, we recommend testing the new earpiece as well as other basic functions of your phone. This way, you can make sure that your repair was successful. Again, use our checklist for this.

    1. Carefully fold the screen around, but do not press it into the case yet.
    2. Turn on your iPhone and call someone.
    3. If something does not work properly, check again if everything is installed and attached correctly.
  20. Installing the cover plates

    • 4 × 1.2 mm Phillips
    • 1 × 1.7 mm Y-Type
    • 1 × 1.6 mm Phillips

    The upper cover plate is additionally hooked on one side.

    1. Position the two cover plates over the connectors. The screw holes help you with the alignment.
    2. Screw the cover plates in place. Fix them with tweezers, so that they do not move.
  21. Installing the display

    iPhone 13 - Installing the display 01
    iPhone 13 - Installing the display 02
    iPhone 13 - Installing the display 03
    iPhone 13 - Installing the display 04
    iPhone 13 - Installing the display 05
    Used tools
    Heat gun

    When folding down the screen make sure not to pinch any flex cables.

    1. If you have applied a new adhesive frame, peel off the remaining protective film at this point.
    2. Flip the screen around and press it firmly into the case frame, so that it sits level all over. You should hear and feel it click into place.
    3. Finally, heat the edge of the screen with hot air in order for the adhesive to bond properly again.
  22. Screwing the screen tight

    • 2 × 6.8 mm Pentalobe
    1. Fix the screen by fastening the two rear case screws again.
Ø 5 (1 Ratings)

Bewerte unsere Anleitung

Hat dir unsere Anleitung weitergeholfen? Wir sind auf deine Beurteilung gespannt.

Submit rating

Submit rating

How did you like this repair guide?

Exceptional

Similar guides

You might also be interested in these guides.

You might be interested in

Get in touch with iDoc

Please contact our customer service for any questions about iDoc's products and services.

  • Send a message

    If you have a question about a guide or want to give us general feedback, just use our contact form

    Write a message
  • Free shipping

    From a minimum order value of 79.00 € your order will be shipped free of charge within Germany.

  • Call iDoc

    If you have any questions about our guides or services, call us from Monday to Friday, 10:00 a.m. to 6:00 p.m.

    +49 30 200 514 455
  • 5 star service

    We offer top quality and service. Our customers confirm this as well.

    Show reviews

Profi-Insights & Tipps für deine erfolgreiche Handy-Reparatur

iDoc schenkt dir den ultimativen Reparatur-Guide GUIDE GRATIS ANFORDERN

Profi-Insights & Tipps für deine erfolgreiche Handy-Reparatur

iDoc schenkt dir den ultimativen Reparatur-Guide GUIDE GRATIS ANFORDERN