OnePlus 5 - Replace camera

Guide to replace the camera for the OnePlus 5

  • OnePlus 5
  • 12 Steps
  • Medium
  • 45 min.
Go to the guide

Introduction

With this guide we show you how to replace the camera of your OnePlus 5. We advice you to check your spare part before installation. If you find any visible errors, please contact your vendor before starting.

The OnePlus 5 is fairly easy to fix, because the screen isn't glued to the frame and there aren't many different screw types. Unclipping the display is a little tricky, though.

Run a data backup before the repair, use a clean work surface and take enough time. If you have questions, use the live chat on our website or write a comment.

Required tools

  • Hartplastik-Plektren

    Hartplastik-Plektren

    You need a flat but stable tool such as a pick to pry out parts that are glued in place.

    €1.00 at the iDoc store
  • iPlastix

    iPlastix

    Dein Smartphone zu öffnen kann eine sehr empfindliche Angelegenheit sein. Die Klinge des biegsamen aber stabilen iPlastix hat eine Dicke von nur 0,15 mm, sodass es auch in den kleinsten Spalten reinpasst, beispielsweise zwischen dem Display und dem Rahmen oder unter dem Logicboard. Das praktische iPlastix ist aus biegsamem Kunststoff und liegt gut in der Hand. Damit ist es der perfekte Helfer bei jeder Smartphone-Reparatur.

    €9.00 at the iDoc store
  • Plastic prying tool

    Plastic prying tool

    You need a flat plastic prying tool to disconnect the various plugs and connectors.

    €1.00 at the iDoc store
  • Steel Laboratory Spatula

    Steel Laboratory Spatula

    You need a flat and sturdy prying tool to disconnect glued parts.

    €9.00 at the iDoc store
  • Suction cup

    Suction cup

    A suction cup is perfect for lifting smooth surfaces such as displays or rear glass panels.

    €2.00 at the iDoc store
  • Phillips PH00 screwdriver

    Phillips PH00 screwdriver

    You need the right screwdriver for removing PH00 screws.

    €10.00 at the iDoc store
  • Torx T1 screwdriver

    Torx T1 screwdriver

    Ganz gleich, ob du Schrauben festdrehen oder lösen möchtest, der Wiha PicoFinish T1 Torx-Schraubendreher eignet sich perfekt für Arbeiten an Geräten mit Torx-Schrauben. Der Schraubendreher wurde in Deutschland hergestellt und ist speziell für Reparaturen an elektronischen Geräten und andere Präzisionsanwendungen ausgelegt. Aufgrund des widerstandsfähigen Chrom-Vanadium-Molybdän-Stahls und seiner hochwertigen Verarbeitung ist dieser Schraubendreher besonders langlebig.

    €13.00 at the iDoc store

Required replacement part

Show all replacement parts for the OnePlus 5 

Replacement parts and tools for this repair

Our tools plus the right spare part help you fix your device easily.

Werkzeugset Torx T1

Wenn dein Smartphone repariert werden muss, kannst du mithilfe der Werkzeuge in diesem Set sämtliche Basisreparaturen selbst...

for €39.00

Getting started

If you get stuck or have questions, you can post a comment for each step. We’d be happy to help.

12 steps
  1. Switch off device

    OnePlus 5 - Switch off device 01
    OnePlus 5 - Switch off device 02
    OnePlus 5 - Switch off device 03

    Turn off your OnePlus 5 completely to protect it from damage.

    1. Press and hold the standby button until the "Switch off" option appears.
    2. Tap again to confirm.
    3. If your OnePlus 5 touchscreen no longer works, you can also turn it off by pressing and holding the standby button for about 10-15 seconds.
  2. Removing the enclosure screws

    OnePlus 5 - Removing the enclosure screws 01
    • 2 × 2.5 mm Torx T1

    To open the OnePlus 5, you need a Torx T1 screwdriver. You can also work with a pentalobe screwdriver, although it doesn't fit right.

    1. Remove both screws on the bottom edge of the case. They are located to the right and left of the USB port and the audio jack.
    2. Place the screws on a common field of the magnetic mat or sorting box.
  3. Remove SIM tray

    OnePlus 5 - Remove SIM tray 01
    OnePlus 5 - Remove SIM tray 02

    Remove the SIM card holder with a SIM tool or paper clip. Push the tool into the small hole on the SIM tray and pull it out.

  4. Remove the back cover

    OnePlus 5 - Remove the back cover 01
    OnePlus 5 - Remove the back cover 02
    OnePlus 5 - Remove the back cover 03
    OnePlus 5 - Remove the back cover 04
    OnePlus 5 - Remove the back cover 05
    OnePlus 5 - Remove the back cover 06
    OnePlus 5 - Remove the back cover 07

    The OnePlus 5 consists of a back cover and a display unit. All the electronics and the screen are installed in the display unit. The back cover is designed as a case.

    Avoid scratches on the OnePlus 5 by placing it on a soft and clean surface.

    To lift off the back cover you need a suction cup, a flat opening tool (like the iPlastix) and a pick. If the screen is badly cracked, cover it with a strip of packing tape so that the suction cup can stick.

    1. Attach the suction cup over the home button. Pull on the suction cup and then slide in the iPlastix or a plastic pick between the display and the rear panel.
    2. A small gap should appear. Here you can insert the pick. It is best to use a hard plastic pick with stopper, so that won't slip too far into the device.
    3. Now slide the pick around the whole frame. You can twist the pick a little to lever off the display. The device is not glued, but clipped. Use the plectrum to release the clips one by one. When all clips are released, you can lift off the back cover. The clips at the upper edge come off last.
    4. The back shell is still connected with a sensitive flex cable. Lift up the back cover and hold it to prevent damaging the cable.
  5. Unplug the connectors

    OnePlus 5 - Unplug  the connectors 01
    OnePlus 5 - Unplug  the connectors 02
    OnePlus 5 - Unplug  the connectors 03
    • 1 × 2.3 mm Phillips
    • Battery connector
    • USB port connector

    The connectors for the battery and the back cover are under a bracket.

    1. Remove the screw from the bracket and remove the bracket. It is latched in on both ends.
    2. First disconnect the battery to avoid short circuits. Disconnect the battery connector with a plastic tool.
    3. Then disconnect the second connector. It connects the USB port to the mainboard.
  6. Removing the camera

    OnePlus 5 - Removing the camera 01
    OnePlus 5 - Removing the camera 02
    OnePlus 5 - Removing the camera 03
    OnePlus 5 - Removing the camera 04
    1. Carefully unplug the camera connectors with a spudger or your fingernail.
    2. Then you can carefully pry out the camera.
  7. Insert the new camera

    OnePlus 5 - Insert the new camera 01
    OnePlus 5 - Insert the new camera 02
    OnePlus 5 - Insert the new camera 03
    OnePlus 5 - Insert the new camera 04
    1. Place the camera in the correct position.
    2. Carefully press the connectors down. They should snap in with a slight click.

    Make sure you do not leave any fingerprints on the lenses during installation.

  8. Attach the connectors

    OnePlus 5 - Attach the connectors 01
    OnePlus 5 - Attach the connectors 02
    OnePlus 5 - Attach the connectors 03
    OnePlus 5 - Attach the connectors 04
    OnePlus 5 - Attach the connectors 05
    OnePlus 5 - Attach the connectors 06
    OnePlus 5 - Attach the connectors 07
    • Connector
    1. Place the back cover perpendicular to the device.
    2. Attach the USB port connector to the main board.
    3. Attach the battery connector to the mainboard.
    4. Attach the bracket and make sure it's latched in at both ends.
    5. Fasten the screw of the bracket.
  9. Attach the back cover

    OnePlus 5 - Attach the back cover 01
    OnePlus 5 - Attach the back cover 02
    OnePlus 5 - Attach the back cover 03
    OnePlus 5 - Attach the back cover 04
    OnePlus 5 - Attach the back cover 05
    1. Put the back cover on the display unit. Attach the upper edge first. The backcover has three clips here.
    2. Clipping the device together takes some strength. It is best to grab the device with both hands and squeeze the edges together with your fingers.

    Press the device together with your fingers, not on the table, to avoid damaging the display.

  10. Insert the SIM tray

    OnePlus 5 - Insert the SIM tray 01
    1. Insert any SIM/SD cards and slide the tray back into the device.
  11. Fasten the back cover screws

    OnePlus 5 - Fasten the back cover screws 01
    • 2 × 2.5 mm Torx T1
    1. Fasten the two screws to the left and right of the USB port.
  12. Test the device

    OnePlus 5 - Test the device 01
    OnePlus 5 - Test the device 02
    OnePlus 5 - Test the device 03
    1. Check the minimum and maximum brightness of the display and check for pixel errors.
    2. Drag any app across the screen in a zig-zag pattern. If it doesn't jump, the touch function is OK.
    3. Also test other functions, such as the cameras, the speaker and the earpiece, using a recording app for example.
Ø 0 (0 Bewertungen)

Bewerte unsere Anleitung

Hat dir unsere Anleitung weitergeholfen? Wir sind auf deine Beurteilung gespannt.

Bewertung abgeben

Bewertung abgeben

Wie findest du unsere Reparatur-Anleitung OnePlus 5 Replace camera?

Exzellent

Similar guides

You might also be interested in these guides.

You might be interested in

Get in touch with iDoc

Please contact our customer service for any questions about iDoc's products and services.

  • Send a message

    If you have a question about a guide or want to give us general feedback, just use our contact form

    Write a message
  • Free shipping

    From a minimum order value of 39.00 € your order will be shipped free of charge within Germany.

  • Call iDoc

    If you have any questions about our guides or services, call us from Monday to Friday, 10:00 a.m. to 6:00 p.m.

    +49 30 200 514 455
  • 5 star service

    We offer top quality and service. Our customers confirm this as well.

    Show reviews