iPhone Xs logic board removal repair guide

You need to clean the logic board.

  • iPhone Xs
  • 15 Steps
  • Difficult
  • 120 min.
Go to the guide

Introduction

Your iPhone Xs has a water damage and you want to remove the logicboard to clean or repair it? In this repair guide, we'll show you how to remove the motherboard of your iPhone Xs.

For each step there is a small video sequence that shows you exactly how to proceed with the repair. The videos can always be started via the play button on the right corner in the first picture at each step.

Be particularly careful when loosening the front camera and FaceID unit and the earpiece, as these cannot be replaced without losing the FaceID function.

Required tools

  • Hartplastik-Plektren

    Hartplastik-Plektren

    You need a flat but stable tool such as a pick to pry out parts that are glued in place.

    €1.00 at the iDoc store
  • Heat gun

    Heat gun

    You can use a heat gun to heat parts that are glued on so they’re easier to remove. In most cases, you can also use a hairdryer.

    from €14.99 on Amazon
  • For storing screws

    For storing screws

    We recommend storing your screws so you don’t mix up the various screws and small parts.

    €10.00 at the iDoc store
  • iFlex opening tool

    iFlex opening tool

    Die kleinen Teile in deinem Smartphone auseinanderzukriegen kann eine sehr große Arbeit bedeuten. Die Klinge des kompakten aber stabilen iFlex hat eine Dicke von nur 0,15 mm, sodass es auch in den kleinsten Spalten reinpasst, beispielsweise zwischen dem Display und dem Rahmen oder unter dem Logicboard. Das praktische iFlex ist aus hochwertigem rostfreiem Stahl und liegt gut in der Hand. Damit ist es der perfekte Helfer bei jeder Smartphone-Reparatur.

    €9.00 at the iDoc store
  • Tweezers

    Tweezers

    We recommend using tweezers to remove screws and various small parts from your device.

    €16.00 at the iDoc store
  • Plastic prying tool

    Plastic prying tool

    You need a flat plastic prying tool to disconnect the various plugs and connectors.

    €1.00 at the iDoc store
  • Suction cup

    Suction cup

    A suction cup is perfect for lifting smooth surfaces such as displays or rear glass panels.

    €2.00 at the iDoc store
  • Pentalobe PL1 screwdriver

    Pentalobe PL1 screwdriver

    You need the right screwdriver for removing pentalobe PL1 screws.

    €10.00 at the iDoc store
  • Phillips PH00 screwdriver

    Phillips PH00 screwdriver

    You need the right screwdriver for removing PH00 screws.

    €10.00 at the iDoc store
  • Y-type Y000 screwdriver

    Y-type Y000 screwdriver

    You need the right screwdriver for removing Y-type screws.

    €10.00 at the iDoc store
Show all replacement parts for the iPhone Xs 

Replacement parts and tools for this repair

Our tools plus the right spare part help you fix your device easily.

Werkzeugset iDoc

Dein Smartphone braucht eine Reparatur? Mit diesem Werkzeug-Set kannst du Reparaturen in Profi-Qualität durchführen. Von...

for €69.00

Getting started

If you get stuck or have questions, you can post a comment for each step. We’d be happy to help.

15 steps
  1. Switching off your device

    iPhone Xs - Switching off your device 01
    iPhone Xs - Switching off your device 02
    1. Turn your iPhone off completely to avoid damaging it during the repair. Press and hold the Standby button and one of the two volume keys for three seconds, until the "Power off" slider appears.
    2. Swipe the slider from left to right. Now your iPhone will shut down completely, which can take about ten seconds.
  2. Removing the back cover screws

    iPhone Xs - Removing the back cover screws 01
    • 2 × 6,8 mm Pentalobe

    You need a pentalobe screwdriver (PL1) to open the iPhone Xs.

    1. Remove the two pentalobe screws at the bottom edge of the back cover. They’re to the right and left of the Lightning connector. Put the screws in the same box of your magnetic pad.
    2. Put your iPhone Xs on a soft, clean surface to avoid scratching the back.
    After being opened, your iPhone Xs loses its guarantee for dust and spray water protection (IP 68 rating).
  3. Removing the display

    iPhone Xs - Removing the display 01
    iPhone Xs - Removing the display 02
    iPhone Xs - Removing the display 03
    iPhone Xs - Removing the display 04
    iPhone Xs - Removing the display 05
    iPhone Xs - Removing the display 06
    1. To lift the front panel, you need a suction cup, a hard plastic pick and a heat gun. If the screen is severely cracked, cover all of it with packing tape before you continue.
    2. The screen is glued to the frame. Use a heat gun to heat the outer edges of the display to about 60°C (140°F).
    3. Place the suction cup over the Home button (if possible) or next to it. While lifting the screen with the suction cup, insert the hard plastic pick between the steel frame and the display frame and press down the steel frame.
    Do not insert your tool more than 5 mm into the gap, so you don't damage small parts inside the iPhone.

    If you can't get a plectrum into the gap, you can use an iFlex. But change to a hard plastic plectrum as soon as possible to avoid scratches on the frame.

    1. Because the display’s glued on all sides, you have to slide the pick all around the iPhone between the steelframe and the display frame. Don’t stick the pick in too far on the side where the Sleep/Wake button is because that could damage the display flex cables.
    2. Now use the pick to push up the display so the tabs disengage from the steel frame. Then you can fold the display over to the side. Rest the display on a stable object to avoid straining the sensitive flex cables.

    Heat the outer edge of the frame several times if necessary.

  4. Disconnecting the battery

    iPhone Xs - Disconnecting the battery 01
    iPhone Xs - Disconnecting the battery 02
    iPhone Xs - Disconnecting the battery 03
    iPhone Xs - Disconnecting the battery 04
    • 1 × 1,2 mm Y-Type
    • 3 × 1,0 mm Y-Type
    • 1 × 3,7 mm Phillips
    • Battery Connector

    Before starting the repair, disconnect the battery contact to prevent short circuits and avoid accidentally turning on your device during the repair.

    1. Use a Y-Type and Phillips screwdriver (Y000/PH00) to remove the screws. Then take off the bracket plate. Put all the parts in the same box of your magnetic pad.
    2. Note that the screws have different lengths

      Apple introduced Y-Type screws with the iPhone 7. They are often wrongly called Tri-Point or Tri-Wing. Use a matching Y-Type screwdriver for these screws so you don't strip the screw heads.

    3. Now very carefully pry off the battery contact by inserting a spudger under the connector.
  5. Disconnecting the display

    iPhone Xs - Disconnecting the display 01
    iPhone Xs - Disconnecting the display 02
    iPhone Xs - Disconnecting the display 03
    iPhone Xs - Disconnecting the display 04
    • Display Connector
    • Earpiece connector
    1. The display unit is connected by three flexible cables.
    2. Use a spudger to separate the connectors for the display and the earpiece one by one.
    3. Be very careful when prying off the connectors using the spudger to prevent damaging anything.
    4. The flex cable of the earpiece is still slightly glued to the cable underneath. Loosen it by carefully pulling it off. Use hot air to help yourself if the adhesive doesn't come off.
    Be especially careful with the cable as there may be problems with FaceID if it gets damaged.
    1. If all connectors are off, you can remove the display. There may still be glue residue on the frame and display.
  6. Information for logicboard removal

    iPhone Xs - Information for logicboard removal 01
    iPhone Xs - Information for logicboard removal 02
    iPhone Xs - Information for logicboard removal 03
    iPhone Xs - Information for logicboard removal 04
    iPhone Xs - Information for logicboard removal 05

    In the following images the speaker, TapticEngine and the battery are missing. These parts do not have to be removed to remove the logic board.To access the upper contacts on the Logicboard, open the front camera and FaceID unit upwards. The module is slightly hooked in on both sides.

  7. Removing the camera

    iPhone Xs - Removing the camera 01
    iPhone Xs - Removing the camera 02
    iPhone Xs - Removing the camera 03
    iPhone Xs - Removing the camera 04
    iPhone Xs - Removing the camera 05
    • 1 × 1,3 mm Y-Type
    • 1 × 1,8 mm Phillips
    • Camera Connector
    1. Loosen the two screws securing the iSight camera cover plate.
    2. Lift up and remove the cover plate. It is hooked into the side of the standby button.
    3. Then separate the two connectors of the double camera with a spudger. Carefully lever and take care not to damage the pins on the logic board.
    4. Lever out the camera with the Spudger and remove it.
  8. Removing the logic board

    iPhone Xs - Removing the logic board 01
    iPhone Xs - Removing the logic board 02
    iPhone Xs - Removing the logic board 03
    iPhone Xs - Removing the logic board 04
    iPhone Xs - Removing the logic board 05
    iPhone Xs - Removing the logic board 06
    • 1 × 3,6 mm Standoff
    • Connectors
    • 1 × 3,1 mm Phillips
    • 1 × 2,3 mm Phillips
    • Connectors

    Two of the contacts on the logic board are still under a cover plate. For the screw with internal thread, also called Standoff screw, you can use a thin slotted screwdriver. There are also special screwdrivers with a cross profile and a pin in the middle.

    1. Remove the Standoff screw and loosen the cover. The bracket is hooked into one side.
    2. Loosen the two contacts carefully with a spudger.

    The contacts are very firmly connected to the logic board and are not easily accessible. If you can't get any further with a Spudger, you can also lever very carefully with tweezers or another thin tool.

    1. Then disconnect all other contacts from the logic board. They connect for example the charging socket, the flashlight and the volume keys.
    2. Then unlock the SIM card holder and take it out.
    3. Loosen the screws of the motherboard.
    4. Then carefully bend all flex cables to the side and remove the logic board.
  9. Installing the logic board

    iPhone Xs - Installing the logic board 01
    iPhone Xs - Installing the logic board 02
    iPhone Xs - Installing the logic board 03
    iPhone Xs - Installing the logic board 04
    iPhone Xs - Installing the logic board 05
    iPhone Xs - Installing the logic board 06
    • 1 × 3,1 mm Phillips
    • 1 × 2,3 mm Phillips
    • 1 × 3,6 mm Standoff
    • Connectors
    1. Make sure that all flex cables are lying flat in the backcover and then insert the logic board. Bend all cables a bit to the side so that you don't trap any of them under the logic board.
    2. Secure the logic board by inserting the screws.
    3. Insert the SIM card holder. You shouldn't feel any strong resistance, otherwise the Logicboard might not fit properly.
    4. Then connect all connectors. Take your time and proceed carefully. Position the connectors above their positions on the logic board and press carefully. The contacts should engage slightly. Don't slide the plugs back and forth and try not to push them tight with force. Use a spudger for the small plugs at the top to push them down.
    5. Hook the cover plate of the two contacts on one side and screw it down.
  10. Inserting the camera

    iPhone Xs - Inserting the camera 01
    iPhone Xs - Inserting the camera 02
    iPhone Xs - Inserting the camera 03
    iPhone Xs - Inserting the camera 04
    iPhone Xs - Inserting the camera 05
    iPhone Xs - Inserting the camera 06
    • 1 × 1,3 mm Y-Type
    • 1 × 1,8 mm Phillips

    Make sure that there is no dust or fingerprints on the camera lenses and on the inside of the camera cover.

    1. Place the iSight camera back in its place and press it down.
    2. Plug in the connectors of the two cameras.
    3. Put the bracket plate in its place. Make sure it hooks into the side of the standby button.
    4. Screw in the bracket plate using the two screws.
  11. Attaching a new frame sticker (optional)

    iPhone Xs - Attaching a new frame sticker (optional) 01
    iPhone Xs - Attaching a new frame sticker (optional) 02
    iPhone Xs - Attaching a new frame sticker (optional) 03
    iPhone Xs - Attaching a new frame sticker (optional) 04
    iPhone Xs - Attaching a new frame sticker (optional) 05
    iPhone Xs - Attaching a new frame sticker (optional) 06
    iPhone Xs - Attaching a new frame sticker (optional) 07
    iPhone Xs - Attaching a new frame sticker (optional) 08

    In the pictures you can see iPhone X. The iPhone Xs is built in the same way and is re-glued in the same way.

    1. To make sure that the new frame sticker will really stick, remove all glue residue and dirt from the metal frame.
    2. Remove the first protective film layer of the frame sticker.
    3. Position the frame sticker carefully on one edge of the frame and attach it gradually. Make sure the frame sticker is positioned evenly and press it on. You can use the plastic spudger to press the adhesive on.
    4. Remove the next large protective film.
    5. You can leave the small protective films on for now and remove them when you've connected the display and attached the bracket plates. This prevents anything from sticking to the frame sticker before you install it. But you can also remove the films right away.

    Please make sure the frame sticker is positioned correctly. Each corner has a different shape, which you can use for orientation.An iPhone repaired with a frame sticker will be protected against dust and spray water, but it will not be 100% waterproof!

  12. Connecting the display

    iPhone Xs - Connecting the display 01
    iPhone Xs - Connecting the display 02
    iPhone Xs - Connecting the display 03
    iPhone Xs - Connecting the display 04
    • Display Connector
    • Earpiece Connector
    1. Place the display unit on the edge of the frame and rest it against a stable object, in order not to overstretch the sensitive flex cables. Make sure your device doesn't slide away.
    2. Connect the two display connectors.
    3. You might need to press down the lower of the two connectors with a spudger to make it sit properly.
    4. Make sure the connectors attach properly. Don't slip and bend the socket contacts on the logic board.
    5. Use tweezers to position the earpiece connector over its socket on the logic board.
    6. Carefully press to attach the connector to its socket.
  13. Connecting the battery

    iPhone Xs - Connecting the battery 01
    iPhone Xs - Connecting the battery 02
    iPhone Xs - Connecting the battery 03
    • Battery Connector
    • 1 × 1,2 mm Y-Type
    • 3 × 1,0 mm Y-Type
    • 1 × 3,7 mm Phillips
    1. Now you can connect the battery connector.
    2. Then insert the bracket plate and fasten with the various screws.
  14. Installing the display

    iPhone Xs - Installing the display 01
    iPhone Xs - Installing the display 02
    iPhone Xs - Installing the display 03
    1. Take the display in both hands and slowly press it down.
    2. Make sure it sits properly everywhere in the frame and gradually press it down all over.

  15. Fastening the back cover screws

    iPhone Xs - Fastening the back cover screws 01
    • 2 × 6,8 mm Pentalobe
    1. Screw the two pentalobe screws to the left and right of the Lightning connector into the enclosure.
Ø 5 (1 Bewertungen)

Bewerte unsere Anleitung

Hat dir unsere Anleitung weitergeholfen? Wir sind auf deine Beurteilung gespannt.

Bewertung abgeben

Bewertung abgeben

Wie findest du unsere Reparatur-Anleitung iPhone Xs Removing the logic board?

Exzellent

Similar guides

You might also be interested in these guides.

You might be interested in

Get in touch with iDoc

Please contact our customer service for any questions about iDoc's products and services.

  • Send a message

    If you have a question about a guide or want to give us general feedback, just use our contact form

    Write a message
  • Free shipping

    From a minimum order value of 39.00 € your order will be shipped free of charge within Germany.

  • Call iDoc

    If you have any questions about our guides or services, call us from Monday to Friday, 10:00 a.m. to 6:00 p.m.

    +49 30 200 514 455
  • 5 star service

    We offer top quality and service. Our customers confirm this as well.

    Show reviews