iPhone 8 camera replacement

The rear-facing camera isn’t working.

  • iPhone 8
  • 14 Steps
  • Medium
  • 30 min.
Go to the guide

Introduction

In this guide, we show you how to replace your iPhone 8’s defective rear camera on your own. You need this repair if the rear camera isn’t working, your pictures are blurry, or the camera doesn’t focus.
Back up all your data before the repair, and touch something like a radiator to get rid of any static charges.

Required tools

  • Hartplastik-Plektren

    Hartplastik-Plektren

    You need a flat but stable tool such as a pick to pry out parts that are glued in place.

    €1.00 at the iDoc store
  • Heat gun

    Heat gun

    You can use a heat gun to heat parts that are glued on so they’re easier to remove. In most cases, you can also use a hairdryer.

    from €14.99 on Amazon
  • For storing screws

    For storing screws

    We recommend storing your screws so you don’t mix up the various screws and small parts.

    €10.00 at the iDoc store
  • Tweezers

    Tweezers

    We recommend using tweezers to remove screws and various small parts from your device.

    €16.00 at the iDoc store
  • Plastic prying tool

    Plastic prying tool

    You need a flat plastic prying tool to disconnect the various plugs and connectors.

    €1.00 at the iDoc store
  • Suction cup

    Suction cup

    A suction cup is perfect for lifting smooth surfaces such as displays or rear glass panels.

    €2.00 at the iDoc store
  • Pentalobe PL1 screwdriver

    Pentalobe PL1 screwdriver

    You need the right screwdriver for removing pentalobe PL1 screws.

    €10.00 at the iDoc store
  • Phillips PH00 screwdriver

    Phillips PH00 screwdriver

    You need the right screwdriver for removing PH00 screws.

    €10.00 at the iDoc store
  • Y-type Y000 screwdriver

    Y-type Y000 screwdriver

    You need the right screwdriver for removing Y-type screws.

    €10.00 at the iDoc store

Required replacement part

  • iPhone 8 iSight Kamera

    iPhone 8 iSight Kamera

    Der Austausch der iSight Kamera (auch Haupt- oder rückseitige Kamera) ist notwendig, wenn diese nicht funktioniert, die Fotos unscharf sind oder die Kamera nicht richtig fokussiert. Auch Flecken auf dem Bild können durch den Austausch verhindert werden. Achtung: Sollten auf den geschossenen Bildern Kratzer zu sehen sein, so befinden sich diese vermutlich auf der Abdeckung des Aluminiumgehäuses und nicht auf der Kameralinse.

    €75.00 at the iDoc store
Show all replacement parts for the iPhone 8 

Replacement parts and tools for this repair

Our tools plus the right spare part help you fix your device easily.

iPhone 8 iSight Kamera

Der Austausch der iSight Kamera (auch Haupt- oder rückseitige Kamera) ist notwendig, wenn diese nicht funktioniert, die Fotos...

for €75.00

Getting started

If you get stuck or have questions, you can post a comment for each step. We’d be happy to help.

14 steps
  1. Switching off your device

    iPhone 8 - Switching off your device 01
    iPhone 8 - Switching off your device 02
    1. Turn your iPhone off completely to avoid damaging it during the repair. Press the Sleep/Wake button for about three seconds until the slider labeled “power off” appears.
    2. Swipe it from left to right. Now your iPhone will shut down completely, which can take about ten seconds.
  2. Removing the enclosure screws

    iPhone 8 - Removing the enclosure screws 01
    • 2 × 3.4mm Pentalobe

    You need a pentalobe screwdriver (PL1) to open the iPhone 7.

    1. Remove the two pentalobe screws at the bottom of the enclosure. They’re to the right and left of the Lightning connector. Put the screws in the same section of your magnetic pad.
  3. Lifting the display

    iPhone 8 - Lifting the display 01
    iPhone 8 - Lifting the display 02
    iPhone 8 - Lifting the display 03
    iPhone 8 - Lifting the display 04
    iPhone 8 - Lifting the display 05
    1. Put your iPhone 8 on a soft, clean surface to avoid scratching the back.
    2. To lift the front panel, you need a suction cup, a hard plastic pick and a heat gun. If the screen is severely cracked, cover all of it with packing tape before you continue.
    3. The screen is glued to the frame. Use a heat gun to heat the outer edges of the display to about 60°C (140°F).

    If necessary, heat the outer edges of the display a few times. Don’t forget that the flexible flat cables for the display are on the side with the Sleep/Wake button. The display is also hooked onto the edge of the earpiece.

    1. Place the suction cup over the Home button (if possible) or next to it. While lifting the screen with the suction cup, insert the hard plastic pick between the aluminum frame and the display frame and press down the aluminum frame. Because the display’s glued on, you have to slide the pick all around the iPhone between the aluminum frame and the display frame. Don’t stick the pick in too far on the side where the Sleep/Wake button is because that could damage the flexible flat display cables.
    2. Now use the pick to push the display so the tabs come out of the aluminum frame. Then you can fold the display over to the side.
    3. Set the display on the aluminum frame so you don’t stretch the flexible flat cables too much.

    Never fold the display further than 180°. It's best not to lay the display flat down, but to lean it against a stable object at an angle.

  4. Disconnecting the battery contact

    iPhone 8 - Disconnecting the battery contact 01
    iPhone 8 - Disconnecting the battery contact 02
    iPhone 8 - Disconnecting the battery contact 03
    • 2 × 2.6 mm Phillips
    • 2 × 1.0 mm Phillips

    Before starting the repair, disconnect the battery contact to prevent short circuits and avoid accidentally turning on your device during the repair.

    1. Use a phillips screwdriver (Ph00) to remove the four phillips screws. Then take off the cover. Put all the parts in the same section of your magnetic pad.
    2. Now carefully lift off the battery contact by inserting a plastic spudger slightly below the connector.
  5. Disconnecting the display connectors

    iPhone 8 - Disconnecting the display connectors 01
    iPhone 8 - Disconnecting the display connectors 02
    iPhone 8 - Disconnecting the display connectors 03
    • Connector

    Use the spudger to disconnect the connectors for the display and Home button.

  6. Disconnecting the FaceTime connector

    iPhone 8 - Disconnecting the FaceTime connector 01
    iPhone 8 - Disconnecting the FaceTime connector 02
    iPhone 8 - Disconnecting the FaceTime connector 03
    • 3 × 1.0 mm Phillips
    1. Use a Phillips screwdriver (PH00) to remove the three Phillips screws. Then take off the cover. Put all the parts in the same section of your magnetic pad.
    2. Using a spudger, carefully disconnect the FaceTime connector from the PCB.
    3. Now you can take off the display all the way.
  7. Removing the iSight camera

    iPhone 8 - Removing the iSight camera  01
    iPhone 8 - Removing the iSight camera  02
    iPhone 8 - Removing the iSight camera  03
    iPhone 8 - Removing the iSight camera  04
    iPhone 8 - Removing the iSight camera  05
    • 1 × 2.9 mm Phillips
    • 1 × 3.0 mm Standoff
    • Connector
    1. Remove the screws which fasten the bracket plate for the iSight camera and remove the bracket plate.
    2. Disconnect the camera by carefully prying off its connector using a spudger.
    3. There are special screwdrivers for removing the internal thread screw, but you can also use a regular, thin slotted screwdriver.

    4. Remove the camera.
  8. Installing the iSight camera

    iPhone 8 - Installing the iSight camera  01
    iPhone 8 - Installing the iSight camera  02
    iPhone 8 - Installing the iSight camera  03
    iPhone 8 - Installing the iSight camera  04
    iPhone 8 - Installing the iSight camera  05
    • Connector
    • 1 × 2.9 mm Phillips
    • 1 × 3.0 mm Standoff
    1. Reinsert the camera into its holder and press into place.
    2. Connect the camera's connector.
    3. Place the bracket plate over the camera and screw it in.
  9. Connecting the FaceTime contact

    iPhone 8 - Connecting the FaceTime contact 01
    iPhone 8 - Connecting the FaceTime contact 02
    iPhone 8 - Connecting the FaceTime contact 03
    iPhone 8 - Connecting the FaceTime contact 04
    • Connector
    • 3 × 1,0 mm Phillips-Schraube
    1. Hold the display upright on the frame and connect the FaceTime contact to the logic board.
    2. Set the display on the side of the frame.
    3. Put the FaceTime contact’s cover back in the iPhone and secure it with the three Phillips screws.
  10. Connecting the display

    iPhone 8 - Connecting the display 01
    iPhone 8 - Connecting the display 02
    iPhone 8 - Connecting the display 03
    • Connector
    1. Connect the two connectors from the Home button and display to the logic board.
  11. Connecting the battery contact

    iPhone 8 - Connecting the battery contact 01
    iPhone 8 - Connecting the battery contact 02
    iPhone 8 - Connecting the battery contact 03
    iPhone 8 - Connecting the battery contact 04
    • Connector
    • 2 × 2.6 mm Phillips
    • 2 × 1,0 mm Phillips-Schraube
    1. Reconnect the battery by connecting the battery contact.
    2. Put the cover back in the iPhone and secure it with the four screws.
  12. Attaching the display

    iPhone 8 - Attaching the display 01
    iPhone 8 - Attaching the display 02
    iPhone 8 - Attaching the display 03
    1. Put the display on the side of the frame and lower it onto the iPhone.
    2. Then press the entire display into the frame.
  13. Fastening the enclosure screws

    iPhone 8 - Fastening the enclosure screws  01
    • 2 × 3.4 mm Pentalobe
    1. Screw the two pentalobe screws to the left and right of the Lightning connector into the enclosure.
  14. Setting the time

    iPhone 8 - Setting the time  01

    When the battery is removed from the device, the iPhone loses the time and sets itself to 1:00 a.m. on 1/1/1970. You could have trouble connecting to the cellular network if the time isn’t set.

    After a repair, complete the following steps:

    1. Synchronize your iPhone with iTunes or connect to a WLAN network and wait until the time is set.
      The time won’t be set automatically unless you enable this feature in the settings.
      Settings > General > Date & Time > Set Automatically
    2. Remove the SIM tray with the SIM card and reinsert it.
    3. Activate airplane mode on the device and then deactivate airplane mode.
      Settings > Airplane Mode
Ø 5 (1 Bewertungen)

Bewerte unsere Anleitung

Hat dir unsere Anleitung weitergeholfen? Wir sind auf deine Beurteilung gespannt.

Bewertung abgeben

Bewertung abgeben

Wie findest du unsere Reparatur-Anleitung iPhone 8 Replace the iSight camera?

Exzellent

Similar guides

You might also be interested in these guides.

You might be interested in

Get in touch with iDoc

Please contact our customer service for any questions about iDoc's products and services.

  • Send a message

    If you have a question about a guide or want to give us general feedback, just use our contact form

    Write a message
  • Free shipping

    From a minimum order value of 39.00 € your order will be shipped free of charge within Germany.

  • Call iDoc

    If you have any questions about our guides or services, call us from Monday to Friday, 10:00 a.m. to 6:00 p.m.

    +49 30 200 514 455
  • 5 star service

    We offer top quality and service. Our customers confirm this as well.

    Show reviews