iPhone 11 Pro - Replacing the screen

Before you start with the repair, we recommend that you test the basic functions of your iPhone 11 Pro using our checklist. This way you can verify after the repair if you have done everything right.

Turn off your iPhone after testing to avoid a potential short circuit during the repair.

1. Press and hold the sleep/wake and the volume button simultaneously for a few seconds to turn it off.
2. Wipe the displayed slider "Switch off" from left to right.
3. Within a few seconds your smartphone will shut down completely.

• 2 × 6.7 mm Pentalobe

The iPhone 11 Pro is opened via the display, which is hooked, glued and additionally attached to the rest of the case with two Pentalobe screws. The screws are attached to the left and right of the Lightning connector.

1. Unscrew the two Pentalobe screws with a special Pentalobe screwdriver.
2. Then put them into a screw storage.

We recommend that you use a screw storage to avoid losing any of the removed parts or screws. You can convert an old sewing box, for example. We at iDoc use our high quality magnetic pad on which you can arrange the parts as they were installed in the phone. This way you can avoid losing screws or mixing them up, which can lead to damage of the device.

In order to be able to remove the glued display after loosening the screws, first heat it up with hot air. Therefore, use a hot air device, such as a heat gun or a regular hair dryer.

1. First place your iPhone on a soft, clean surface to avoid scratches on the case.
2. Then heat the edge of the display by running the heat gun evenly over it.

When the glue of the display is sufficiently warmed up, you can start to loosen it carefully.

Opening the iPhone 11 Pro will void the manufacturer's warranty, as well as the warranty for protection against dust and water of the IP68 classification.

1. Start by placing a suction cup on the bottom edge of the display. Pull it slowly upwards to create a narrow gap between the display and the case.
2. Then insert a flat stable tool into the gap to enlarge it. We recommend a hard plastic plectrum and the iFlex for this purpose.

The hard plastic plectrum is only thinner at the corners. On the one hand this facilitates insertion, on the other hand this prevents you from inserting the plectrum too far into the device. The iFlex is made of extra thin, stable metal and has sharp edges. To avoid scratches on the frame of your device, we recommend that you start this step with the iFlex and continue with the hard plastic plectrum as early as possible.

Once a gap is created, you can detach the display from the rest of the housing unit piece by piece.

1. Move the hard plastic plectrum once completely around the display frame. Press it upwards at the same time to release the hooked lugs of the display from the rear case.

You can reheat the glue with hot air at regular intervals to make it easier to remove.

1. When the display is completely detached, you can carefully open it towards the standby button. Lean it against a stable object to avoid overstretching the flex cables.

• 2 × 1.5 mm Y-Type
• Connector
• 4 × 1.46 mm Y-Type
• Connector

As one of the first steps the battery should always be disconnected to avoid short circuits during the repair. The iPhone 11 Pro battery has two connectors, one on the logicboard and one on the lightning connector. The procedure is the same for both connectors:

1. First remove the bracket plate over the battery connector by unscrewing the Y-type screws.

When detaching connectors, always start from the side where there are no small components on the board. This way you avoid potential damage.

1. Then use a plastic lever tool to move under the connector and carefully separate it from the board. We use a plastic spudger for this.

• 6 × 1.16 mm Y-Type
• Connectors

To be able to remove the display completely, the display connectors are detached from the logicboard. Removing the display makes it easier and safer to replace the battery, because the flex cables of the display are no longer in the way.

1. First remove the bracket plate over the display connectors by loosening the Y-type screws.

1. Drive a spudger under the three connectors and carefully lift them off the logicboard one after the other.
2. Then put the detached display to the side.

• 1 × 1.75 mm Y-Type
• 1 × 1.30 mm Y-Type
• 1 × 1.25 mm Y-Type

The earpiece must be transferred from the old display to the new one to use Face ID as usual. It is integrated on the sensor cable, which must also be transferred.

1. To remove the earpiece you have to unscrew the three screws with which it is fixed on the display unit.
2. Loosen the earpiece from the sensor cable with tweezers and fold it over.
3. Move a steel spatula under the sensor cable and carefully remove it piece by piece from the display unit.
4. Also use the steel spatula or tweezers to lever the sensors out of their leads on the upper edge of the display.

If the old display has been removed, you can prepare the replacement display by peeling off all protective foils and seals.

• 1 × 1.75 mm Y-Type
• 1 × 1.3 mm Y-Type
• 1 × 1.25 mm Y-Type

At this point you can install the removed earpiece together with the sensor cable on the replacement display.

1. Align the earpiece with the upper edge of the display unit and push the sensors back into their leads.

1. Then fold the earpiece back onto the sensor cable and screw it tight.

• Connectors
• 6 × 1.16 mm Y-Type

At this point you can reconnect the display to the logicboard.

1. Lean the display back against a stable object to avoid overstretching the flex cables when connecting them.

Never attach connectors by force. Damage to a connector or the slot can lead to the failure of an entire component.

1. Attach the three display connectors by carefully pressing them one after the other on the logicboard.
2. Position the bracket plate over the attached connectors and fix it with the six Y-type screws.

• Connector
• 4 × 1.46 mm Y-Type
• Connector
• 2 × 1.15 mm Y-Type

After the display, the battery can be reconnected as well. You should always connect it last to avoid short circuits during the repair. The procedure is again valid for both battery connectors:

1. Carefully press the battery connector on the board so that it clicks into place audibly and noticeably.
2. Position the bracket plate over the connector and screw it on.

Before you glue your device again, we strongly recommend that you check the functionality of your new display at this point. For example, test the brightness, or the touch by zigzagging an app across the display.

To make sure that your repair was successful, you should also check other basic functions of your iPhone. Please refer to our checklist again for help. If something doesn't work after the repair, check make sure everything is installed and connected correctly.

After testing your device you can attach the display again. Usually, the adhesive residues are sufficient to fasten the display properly again. If this is not the case, you have to remove the old adhesive frame and attach a new one.

1. To do this, carefully fold it over and press it evenly into the rear case, so that it clicks into place.

• 2 × 6.7 mm Pentalobe

At the end of the repair the display must still be screwed.

1. Fasten the Pentalobe screws left and right of the Lightning connector.