Apple iPad mini 2 - Removing the logic board

Check the logic board/Lightning connector

  • iPad mini 2
  • 21 Steps
  • Difficult
  • 90 min.
Go to the guide

Introduction

In this guide, we show you how to remove your iPad mini 2’s logic board on your own. You need to remove the logic board if you want to clean it or solder on a new Lightning connector.

Required tools

  • Hartplastik-Plektren

    Hartplastik-Plektren

    You need a flat but stable tool such as a pick to pry out parts that are glued in place.

    €1.00 at the iDoc store
  • Heat gun

    Heat gun

    You can use a heat gun to heat parts that are glued on so they’re easier to remove. In most cases, you can also use a hairdryer.

    from €14.99 on Amazon
  • For storing screws

    For storing screws

    We recommend storing your screws so you don’t mix up the various screws and small parts.

    €10.00 at the iDoc store
  • Menda ESD Spudger

    Menda ESD Spudger

    You need a flat plastic prying tool to disconnect the various plugs and connectors.

    €5.00 at the iDoc store
  • Steel Laboratory Spatula

    Steel Laboratory Spatula

    You need a flat and sturdy prying tool to disconnect glued parts.

    €9.00 at the iDoc store
  • Suction cup

    Suction cup

    A suction cup is perfect for lifting smooth surfaces such as displays or rear glass panels.

    €2.00 at the iDoc store
  • Phillips PH00 screwdriver

    Phillips PH00 screwdriver

    You need the right screwdriver for removing PH00 screws.

    €10.00 at the iDoc store
Show all replacement parts for the iPad mini 2 

Replacement parts and tools for this repair

Our tools plus the right spare part help you fix your device easily.

Werkzeugset Samsung

Ganz gleich, welches Problem dein Handy hat - mit unserem Werkzeugset kannst du es bestimmt beheben. Dieses Reparaturset...

for €49.00

Getting started

If you get stuck or have questions, you can post a comment for each step. We’d be happy to help.

21 steps
  1. Inserting the picks

    iPad mini 2 - Inserting the picks 01
    iPad mini 2 - Inserting the picks 02
    iPad mini 2 - Inserting the picks 03
    iPad mini 2 - Inserting the picks 04
    iPad mini 2 - Inserting the picks 05
    iPad mini 2 - Inserting the picks 06

    The iPad mini 2’s touchscreen is glued firmly in place. To detach it, you have to constantly heat it with a heat gun so the glue will soften (see figures 1 and 2). Make sure you only heat the edge of the display. Then you have to insert a plastic pick into the gap between the frame and the display to detach the adhesive.

    1. Turn off the iPad.
    2. Start with the left and right sides, where there’s only a small adhesive strip. Insert a laboratory spatula about 4 millimeters between the aluminum frame and the display frame (see figure 3). Be very careful to avoid damaging the LCD under them or the touchscreen with the spatula. Alternatively, you can lift the glass with a suction cup. At the same time, insert a pick between the aluminum frame and the display frame.

    Once you’ve inserted the first pick, you can lift the screen slightly. Continue heating the edge of the display during this process.

    Now use more picks to work your way around the display one time (see figures 4 and 5).

    Don’t work on the side where the Home button is until the next step. The important flexible flat cables under it could get damaged.

  2. Lifting the touchscreen

    iPad mini 2 - Lifting the touchscreen 01
    iPad mini 2 - Lifting the touchscreen 02
    1. As soon as you’ve finished with the upper part of the glass, you can slowly lift the screen at the part where the FaceTime camera is. At the same time, heat the bottom of the iPad mini 2 where the Home button is (see figure 1). You should be able to feel the glue slowly coming undone while you continue to carefully lift and heat the screen.
    2. Once the glue is fully dissolved, you can lift the screen all the way, fold it over and set it down (see figure 2). Make sure you don’t stretch the LCD and touchscreen cables too much.Avoid getting fingerprints on the LCD. If necessary, you can wear latex gloves.
  3. Removing the LCD screws

    iPad mini 2 - Removing the LCD screws 01
    iPad mini 2 - Removing the LCD screws 02
    iPad mini 2 - Removing the LCD screws 03
    iPad mini 2 - Removing the LCD screws 04
    iPad mini 2 - Removing the LCD screws 05
    1. First remove the adhesive strips at the four corners of your iPad. There are screws below them (see figure 1).
      There are also magnets to hold the Smart Cover in place.
    2. Now remove the three stickers from the LCD (see figures 2 to 4).
    3. Then unscrew the four Phillips screws.
      3 x 3.3 mm Phillips screws
      1 x 4.5 mm Phillips screw
  4. Lifting the LCD

    iPad mini 2 - Lifting the LCD 01
    iPad mini 2 - Lifting the LCD 02
    1. The LCD is lightly glued to the rear panel all along the sides. Carefully insert the laboratory spatula at the edges between the silver rear panel and the LCD to slowly detach the glue (see figures 1 and 2).
    Make sure you don’t bend the LCD too much.
  5. Removing the rear panel

    iPad mini 2 - Removing the rear panel 01
    iPad mini 2 - Removing the rear panel 02
    1. There are seven identical Phillips screws holding the silver rear panel in place. Remove them.
      7 x 1.7 mm Phillips screws
    2. Now lift the rear panel and remove it.
  6. Disconnecting the battery connector

    iPad mini 2 - Disconnecting the battery connector 01
    iPad mini 2 - Disconnecting the battery connector 02
    iPad mini 2 - Disconnecting the battery connector 03
    1. Now remove the three Phillips screws from the silver cable cover (see figure 1).
      2 x 1.3 mm Phillips screws
      1 x 2.8 mm Phillips screw
    2. Then lift the cover to remove it (see figure 2).
    3. Now carefully lift off the battery connector by inserting the flat end of the ESD spudger slightly below the connector (see figure 3). If you don’t have a spudger, you can also try using your fingernail.
      You can also go ahead and remove the battery at this point by skipping ahead to step 13, but we don’t recommend it because you could damage other parts during removal.
  7. Disconnecting the display cables

    iPad mini 2 - Disconnecting the display cables 01
    iPad mini 2 - Disconnecting the display cables 02
    iPad mini 2 - Disconnecting the display cables 03
    1. Disconnect the LCD connector (see figure 1). Be very careful. Insert the flat end of the spudger very slightly below the contact and lift it up. Now you can remove the LCD.
    2. Disconnect the touchscreen connector (see figure 2). Once again, be very careful.
      The cable is still lightly glued in place. Use the spudger to detach the glue (see figure 3).
  8. Removing the right Wi-Fi antenna

    iPad mini 2 - Removing the right Wi-Fi antenna 01
    iPad mini 2 - Removing the right Wi-Fi antenna 02
    iPad mini 2 - Removing the right Wi-Fi antenna 03
    iPad mini 2 - Removing the right Wi-Fi antenna 04
    1. Carefully peel off all the marked stickers (see figure 1).
    2. Now remove the four Phillips screws (see figure 2).
      3 x 1.5 mm Phillips screws
      1 x 2.6 mm Phillips screw
    3. The antenna is stuck to the speaker under it. Carefully remove it using the laboratory spatula (see figure 3).
    4. Now slowly pull out the antenna cable and carefully lift off the antenna connector using the spatula (see figure 4).
  9. Removing the left Wi-Fi antenna

    iPad mini 2 - Removing the left Wi-Fi antenna 01
    iPad mini 2 - Removing the left Wi-Fi antenna 02
    iPad mini 2 - Removing the left Wi-Fi antenna 03
    iPad mini 2 - Removing the left Wi-Fi antenna 04
    iPad mini 2 - Removing the left Wi-Fi antenna 05
    iPad mini 2 - Removing the left Wi-Fi antenna 06
    1. Remove the angled sticker (see figures 1 and 2).
      The antenna cable is under it.
    2. Now remove the three Phillips screws (see figure 3).
      2 x 1.5 mm Phillips screws
      1 x 2.6 mm Phillips screw
    3. The antenna is stuck to the speaker under it. Carefully remove it using the laboratory spatula (see figure 4).
    4. Now slowly pull out the antenna cable (see figure 5) and carefully lift off the antenna connector using the spatula (see figure 6).
  10. Removing the speaker screws

    iPad mini 2 - Removing the speaker screws 01
    iPad mini 2 - Removing the speaker screws 02
    1. Remove the two identical Phillips screws.
      2 x 1.8 mm Phillips screws
    2. Remove the two washers below them (see figure 2).
  11. Removing the speakers

    iPad mini 2 - Removing the speakers 01
    iPad mini 2 - Removing the speakers 02

    Now use the laboratory spatula to push out the two speakers (see figures 1 and 2).

  12. Removing the logic board

    iPad mini 2 - Removing the logic board 01
    iPad mini 2 - Removing the logic board 02
    iPad mini 2 - Removing the logic board 03
    iPad mini 2 - Removing the logic board 04
    iPad mini 2 - Removing the logic board 05
    1. Remove the three Phillips screws (see figure 1).
      2 x 1.9 mm Phillips screws
      1 x 1.3 mm Phillips screw
    2. Heat the surfaces where the Lightning connector cable and the iSight camera are from the back (see figure 2).
    3. Now insert the spudger below the logic board. It’s only lightly glued on in two places (see figures 3 and 4). Then remove it (see figure 5).
  13. Installing the logic board

    iPad mini 2 - Installing the logic board 01
    1. Put the logic board back in and screw it in place.
      2 x 1.9 mm Phillips screws
      1 x 1.3 mm Phillips screw
  14. Attaching the speakers

    iPad mini 2 - Attaching the speakers 01
    iPad mini 2 - Attaching the speakers 02
    1. Now push the two speakers back into the gaps in the enclosure.
    2. Put the washers back on (see figure 1) and screw the speakers in place with the two Phillips screws (see figure 2).
      2 x 1.8 mm Phillips screws
  15. Installing the left Wi-Fi antenna

    iPad mini 2 - Installing the left Wi-Fi antenna 01
    iPad mini 2 - Installing the left Wi-Fi antenna 02
    iPad mini 2 - Installing the left Wi-Fi antenna 03
    1. Connect the Wi-Fi antenna with the long cable again and install it just like before. Make sure you compare it with figure 1.
    2. Attach the antenna to the speaker again and screw it in place (see figure 2).
      2 x 1.5 mm Phillips screws
      1 x 2.6 mm Phillips screw
    3. Now put the sticker back on (see figure 3).
  16. Installing the right Wi-Fi antenna

    iPad mini 2 - Installing the right Wi-Fi antenna 01
    iPad mini 2 - Installing the right Wi-Fi antenna 02
    1. Connect the Wi-Fi antenna with the long cable again and install it just like before. Make sure you compare it with figure 1.
    2. Attach the antenna to the speaker again and screw it in place (see figure 2).
      2 x 1.5 mm Phillips screws
      1 x 2.6 mm Phillips screw
    3. Now put the sticker back on (see figure 3).
  17. Connecting the cables

    iPad mini 2 - Connecting the cables 01
    iPad mini 2 - Connecting the cables 02
    1. Connect the new touchscreen’s cable and gently press it on at the point where it was glued on.
    2. Now you can install the LCD cable again (see figure 2).
  18. Connecting the battery

    iPad mini 2 - Connecting the battery 01
    iPad mini 2 - Connecting the battery 02
    1. Now connect the battery connector again.
    2. Put the silver cover back on and screw it in place (see figure 2).

    2 x 1.3 mm Phillips screws
    1 x 2.8 mm Phillips screw

  19. Attaching the rear panel

    iPad mini 2 - Attaching the rear panel 01
    1. Put the rear panel back in and screw it in place.
    2. 7 x 1.7 mm Phillips screws
  20. Attaching the LCD

    iPad mini 2 - Attaching the LCD 01
    iPad mini 2 - Attaching the LCD 02
    1. Now put the LCD back in the frame.Make sure you don’t leave any fingerprints on the display. If necessary, we recommend using latex gloves.
    2. Now fasten the four Phillips screws and make sure the magnets are positioned correctly.
      3 x 3 mm Phillips screws
      1 x 4.5 mm Phillips screw
    3. Attach the adhesive strips to the LCD again (see figure 2).
  21. Attaching the touchscreen

    iPad mini 2 - Attaching the touchscreen 01
    iPad mini 2 - Attaching the touchscreen 02
    1. Now you can attach the screen again. First peel the protective film off the inside of the screen and see if there are any fingerprints.

      Make sure there are no fingerprints or dust on the LCD. Remove any fingerprints with a microfiber cleaning cloth. You can use an air compressor or compressed air spray to blow away the dust.
    2. Now remove the protective strips from the adhesive strip.
    3. Then put on the touchscreen quickly but precisely so no new dust can settle on the LCD.
    4. Press on the screen at the edges and then weight it down for a long time, for example with a few books, so it’s pressed firmly onto the enclosure.
Ø 5 (1 Bewertungen)

Bewerte unsere Anleitung

Hat dir unsere Anleitung weitergeholfen? Wir sind auf deine Beurteilung gespannt.

Bewertung abgeben

Bewertung abgeben

Wie findest du unsere Reparatur-Anleitung iPad mini 2 Removing the logic board?

Exzellent

Comments

Similar guides

You might also be interested in these guides.

Get in touch with iDoc

Please contact our customer service for any questions about iDoc's products and services.

  • Send a message

    If you have a question about a guide or want to give us general feedback, just use our contact form

    Write a message
  • Free shipping

    From a minimum order value of 39.00 € your order will be shipped free of charge within Germany.

  • Call iDoc

    If you have any questions about our guides or services, call us from Monday to Friday, 10:00 a.m. to 6:00 p.m.

    +49 30 200 514 455
  • 5 star service

    We offer top quality and service. Our customers confirm this as well.

    Show reviews